Agilent Technologies N5230C User Manual

Index-6 Service Guide N5230-90024
Index
procedure, 7-40
replaceable parts
illustrated
, 6-45
part numbers
, 6-42
unique files located on
, 7-40
hard disk drive (parallel ATA)
illustrated, 6-43
replaceable parts
illustrated
, 6-43
hard disk drive (serial ATA)
illustrated, 6-45
part number
, 6-44
replaceable parts
part numbers
, 6-44
hardware
in bottom assembly
illustrated
, 6-35
part numbers
, 6-34
in external analyzer
illustrated
, 6-39
part numbers
, 6-38
in hard disk drive (parallel ATA)
assembly
illustrated
, 6-43
in hard disk drive (serial ATA)
part numbers
, 6-44
in hard disk drive (serial ATA)
assembly
illustrated
, 6-45
in hard disk drive assembly
part numbers
, 6-42
in internal analyzer
illustrated
, 6-37
part numbers
, 6-36
in rear panel assembly
illustrated
, 6-41
part numbers
, 6-40
in top assembly
illustrated
, 6-33
part numbers
, 6-32
location of part numbers
, 6-7
options, 2-3, 8-15
high dynamic range
configurable test set configuration,
5-18
configuration
diagram
, 5-18
I
IDE
data storage, 5-25
insertion loss
check
failure of
, 3-14
test port cables
, 3-14
installing
a serial number, 8-17
instruction documentation symbol , 1-8
instrument markings , 1-8
instrument specifications , 3-6
interconnects
AUX I/O
pin assignments
, 5-14
front panel, 5-23
USB
, 5-23
HANDLER I/O
pin assignments
, 5-13
rear panel
, 5-10, 5-11, 5-24
1284-C
, 5-25
AUX I/O, 5-11
Display
, 5-25
EXT 10 MHz REF IN
, 5-10
EXT 10 MHz REF OUT
, 5-10
GPIB
, 5-24
HANDLER I/O
, 5-11
LAN
, 5-25
PARALLEL
, 5-25
RS-232
, 5-24
SERIAL
, 5-24
TEST SET I/O
, 5-11
TRIG IN
, 5-11
TRIG OUT, 5-11
USB
, 5-24
VGA
, 5-25
TEST SET I/O
pin assignments
, 5-12
internal analyzer
replaceable hardware
illustrated, 6-37
part numbers
, 6-36
replaceable parts
illustrated
, 6-37
part numbers
, 6-36
inverter board
removal and replacement
illustrated, 7-11
procedure
, 7-10
IP address, LAN , 4-19
ISM1-A mark , 1-8
isolation
cause of failure, 8-13
definition of, 8-13
measurements affected by
, 8-13
K
keypad assembly
illustrated, 6-11
operation, 5-23
part number
, 6-10
removal and replacement
illustrated
, 7-11
procedure
, 7-12
test
, 4-14
troubleshooting, 4-12
kits
calibration, 2-8, 3-6
handle
part numbers
, 6-48
rack mount
part numbers
, 6-48
upgrade
part numbers
, 6-47
verification
, 2-8, 3-6
knob
front panel
illustrated
, 6-9
part number
, 6-8
test
, 4-15
troubleshooting
, 4-12
L
LAN
connector
rear panel
, 5-25
cross-over cable
, 4-21
IP address
, 4-19
ping command, 4-19
ping to and from
, 4-19
subnet mask
, 4-19
testing between analyzers, 4-21
troubleshooting
, 4-19
LED board, front panel
illustrated, 6-35
part number, 6-34
linearity
source power
test
, 3-29
test port output power
test
, 3-29
lithium battery
removal and replacement, 7-52
illustrated, 7-53
lithium battery disposal , 1-9
LO power
adjustment, 3-36
load match
cause of failure, 8-11
definition of, 8-11
measurements affected by
, 8-11, 8-12
locating
assembly part numbers, 6-7
hardware part numbers, 6-7
miscellaneous part numbers
, 6-7
replaceable part numbers
by reference designator
, 6-6
by type of part
, 6-7
M
MA 26.5
illustrated, 6-25, 6-29

Agilent Technologies N5230C Specifications

General

Brand	Agilent Technologies
Model	N5230C
Category	Measuring Instruments
Language	English