Table of Figures
vi
Series AE1F, AE1L, AE.E, AE.N, AE.H, AE.V, AED1E,
AED2N ID, ZD construction types
BA-2011.11
760.0002 GB - 150 500
Table of Figures
Fig. 1 Nameplate (example) ............................ 7
Fig. 2 ATEX nameplate ................................... 7
Fig. 3 Model code ............................................ 7
Fig. 4 Check for twisting ................................ 14
Fig. 5 Check coupling alignment ................... 14
Fig. 6 Check lateral and height misalignment15
Fig. 7 Check angular misalignment ............... 15
Fig. 8 Cutting the packing rings ..................... 23
Fig. 9 Removing the joint clamp .................... 27
Fig. 10 Removing the joint sleeve ................. 27
Fig. 11 Removing the bushes for joint bolt .... 27
Fig. 12 Pressing out the drive shaft ............... 28
Fig. 13 Removing the bearing ....................... 30
Fig. 14 Two single-row angular contact ball
bearings with spacer rings ............ 32
Fig. 15 Joint of the outermost encasement
points against the direction of
installation ..................................... 33
Fig. 16 Pulling in the drive shaft .................... 35
Fig. 17 Pressing in the joint bush .................. 35
Fig. 18 Securing the joint sleeve .................. 36
Fig. 19 Apply pressure to the joint clamp strap
on the joint clamp seal. ................. 36
Fig. 20 Band-It clamping tool and adapter J050
...................................................... 37
Fig. 21 Tightening the joint clamps ................ 37
Fig. 22 Shearing off the joint clamp ............... 37
Fig. 23 Canting and shearing off the joint
clamp ............................................. 37
Fig. 24 Sectional drawing for series AE1F,
AE1L, AE1E, AE2E, AE1N, AE2N,
AE4N, AED1E, AED2N; ID
construction type ........................... 43
Fig. 25 P02 Stuffing box with flushing ring .... 44
Fig. 26 P03 stuffing box with internal seal
chamber ring ................................. 44
Fig. 27 P04 stuffing box with external seal
chamber ring ................................. 44
Fig. 28 G0K and G0N mechanical seal, single-
acting ............................................. 44
Fig. 29 G0S and G0T, mechanical seal, single-
acting with throttle ring .................. 44
Fig. 30 G0Q mechanical seal, single-acting
with quench ................................... 44
Fig. 31 G0D double-acting mechanical seal.. 44
Fig. 32 Sectional drawings for series AE1+1H,
AE2+2H, AE2+2V, AE4+4V; ID
construction type ........................... 45
Fig. 33 Sectional drawings for series AE2H,
AE4H; ID construction type .......... 46
Fig. 34 Sectional drawing of series AE1N,
AE2N; ZD construction type ......... 47
Fig. 35 Sectional drawings of series AE1+1H,
AE2+2H; ZD construction type ..... 48
Fig. 36 Sectional drawings of series AE2H,
AE4H; ZD construction type ......... 49
Fig. 37 Clearance certificate ......................... 52
Listing of Tables
Tab. 1 Who should read these instructions .... 1
Tab. 2 Other applicable documents ................ 1
Tab. 3 Overview of dangers ............................ 1
Tab. 4 Symbols and their meaning ................. 1
Tab. 5 Noise level ........................................... 9
Tab. 6 Valvoline preservatives ...................... 11
Tab. 7 Cleaning agents ................................. 12
Tab. 8 Overview of antifriction bearing grease
...................................................... 22
Tab. 9 Packing ring dimensions .................... 25
Tab. 10 Pump series with spacer rings ......... 31
Tab. 11 Pump series with two angular contact
ball bearings ................................. 31
Tab. 12 Single part labeling .......................... 42
Tab. 13 Overview of potential disturbances .. 50
Tab. 14 Troubleshooting disturbances ......... 51
To Next Page
Loading...
