What to do if Alto-Shaam CT PROFORMANCE CTP6-10E displays 'E25 - B3 Condensor Probe Fault'?
If your Alto-Shaam oven displays the error 'E25 - B3 Condensor Probe Fault', you should: * Check the B3 condensor temperature probe for defects. * Ensure the B3 condensor probe wires are connected correctly.
What to do if my Alto-Shaam CT PROFORMANCE CTP6-10E Oven shows 'E105 - No or Low Water Pressure'?
If your Alto-Shaam oven is showing an 'E105 - No or Low Water Pressure' error, you should: * Check if the water supply is not connected. * Check if the water supply is shut off. * Check if the water supply to the unit is blocked or obstructed. * Inspect the pressure switch for faults.
What does error 'E03 - Fan Motor Error' mean on my Alto-Shaam Oven?
If your Alto-Shaam oven displays the 'E03 - Fan Motor Error', you should: * Check the wiring to all listed components. * If the LED on the motor control flashes, refer to the error codes for motor control. * Check if the motor or fan wheel is locked. * Inspect the Hall sensor for proper detection. * Check for motor thermo temperature protection. * Inspect the fan wheel for damages.
What does 'E222 - Lower VFD Overheating' mean on my Alto-Shaam CT PROFORMANCE CTP6-10E Oven?
If your Alto-Shaam oven displays the 'E222 - Lower VFD Overheating' error, you should: * Check for an overheat condition. * Inspect the high limit switch for defects. * Check if the cooling fans are defective.
How do I troubleshoot 'e55 - Vent Not Open (Lower vent on dual vent system)' on my Alto-Shaam CT PROFORMANCE CTP6-10E Oven?
If your Alto-Shaam oven displays the error 'e55 - Vent Not Open (Lower vent on dual vent system)', you should: * Check for alignment issues between the motor cam and vent motor safety switch (micro switch). * Inspect the faulty vent valve (motor). * Check the faulty vent valve safety switch (micro switch).
What does 'E103 - Option Board Doesn’t Send Switch Setting' mean on my Alto-Shaam Oven?
If your Alto-Shaam oven displays the error 'E103 - Option Board Doesn’t Send Switch Setting', you should: * Check the CAN cable connection between the OB and CB. * Ensure the CB dip switch is set to see an OB. * Check for compatible OB and CB software. * Inspect the OB and CB for defects.
How do I resolve 'E106 - Boiler Drain Pump Fault' on my Alto-Shaam CT PROFORMANCE CTP6-10E Oven?
If your Alto-Shaam oven displays the 'E106 - Boiler Drain Pump Fault' error, you should: * Check if the drain pump motor is running or defective. * Inspect the hall effect sensor for damage or miswiring. * Check if the motor is improperly wired.
What to do if Alto-Shaam CT PROFORMANCE CTP6-10E displays 'E20 - B11 Core Temperature Probe Single Point Fault'?
If your Alto-Shaam oven displays the error 'E20 - B11 Core Temperature Probe Single Point Fault', you should: * Clean probe receptacle pins with sandpaper. * Check the B11 single point core temperature probe with quick connect for defects. * Ensure the B11 single point core temperature probe wires are connected. * Inspect the B11 single point core temperature probe receptacle for defects and ensure its wires are connected.
What does 'E104 - Option Board Not Communicating' mean on my Alto-Shaam CT PROFORMANCE CTP6-10E Oven?
If your Alto-Shaam oven displays the error 'E104 - Option Board Not Communicating', you should: * Check the option board CAN connection at the CB and OB. * Inspect the OB and CB for defects.
How do I resolve 'E108 - Cooling Fan Failure' on my Alto-Shaam CT PROFORMANCE CTP6-10E?
If your Alto-Shaam oven displays the 'E108 - Cooling Fan Failure' error, you should: * Inspect if the cooling fan is damaged. * Check if the cooling fan is blocked or the blades are restricted. * Ensure the incoming air temperature does not exceed 100°F (38°C). * Check if the air inlet has become blocked.
General| Model | CT PROFORMANCE CTP6-10E |
|---|---|
| Category | Oven |
| Power Supply | Electric |
| Control Type | Digital |
| Construction | Stainless Steel |
| Features | programmable touchscreen controls |
To Next Page