To Next PageTo Next PageWhat does 'E06 - Lower VFD Comm Failure' mean on my Alto-Shaam Oven and how can I fix it?
If your Alto-Shaam oven displays the 'E06 - Lower VFD Comm Failure' error, you should: * Check for loss of power to the VFD. * Inspect for a VFD malfunction. * Check if the CAN cable is disconnected and ensure the CAN address is correct on the VFD.
What does 'E05 - VFD Comm Failure' mean on my Alto-Shaam Oven and how to fix it?
If your Alto-Shaam oven displays the 'E05 - VFD Comm Failure' error, you should: * Check for loss of power to the VFD. * Inspect for a VFD malfunction. * Check if the CAN cable is disconnected and ensure the CAN address is correct on the VFD.
Why does my Alto-Shaam CT PROFORMANCE CTP6-10E display 'E01 - Low Water Boiler'?
If your Alto-Shaam oven displays the 'E01 - Low Water Boiler' error, you should: * Check the water supply to ensure it's turned on. * Check for low water pressure. * Verify the boiler drain cap is present. * Inspect the boiler drain pump and check for leaks in the drain pump elbow. * Clean the water level probe for calcium buildup. * Check the double water solenoid valve (Y1). * Inspect the relay board for high voltage issues.
What to do if my Alto-Shaam CT PROFORMANCE CTP6-10E displays 'E212 - VFD Overheating'?
If your Alto-Shaam oven displays the 'E212 - VFD Overheating' error, you should: * Check for an overheat condition. * Inspect the high limit switch for defects. * Check if the cooling fans are defective.
How do I resolve 'E108 - Cooling Fan Failure' on my Alto-Shaam CT PROFORMANCE CTP6-10E?
If your Alto-Shaam oven displays the 'E108 - Cooling Fan Failure' error, you should: * Inspect if the cooling fan is damaged. * Check if the cooling fan is blocked or the blades are restricted. * Ensure the incoming air temperature does not exceed 100°F (38°C). * Check if the air inlet has become blocked.
What does 'E02 - Control Temperature High' mean on an Alto-Shaam CT PROFORMANCE CTP6-10E Oven?
If your Alto-Shaam oven displays the 'E02 - Control Temperature High' error, you should: * Check wiring to all components listed. * Inspect the cooling fan on the relay board assembly, the display board assembly, the main cooling fan, and the cooling fan on the motor drive.
What causes 'E15 - Condensor Temperature High' error in Alto-Shaam CT PROFORMANCE CTP6-10E Oven?
If your Alto-Shaam oven shows the error 'E15 - Condensor Temperature High', you should: * Check if the water supply is shut off. * Check wiring to all components mentioned. * Inspect the B3 condensor temperature probe for defects and ensure the B3 condensor probe wires are connected correctly. * Inspect the single water solenoid valve (Y2). * Inspect the relay board for high voltage issues.
How to troubleshoot 'E13 - Boiler Temperature High' error on Alto-Shaam Oven?
If your Alto-Shaam oven displays the 'E13 - Boiler Temperature High' error, you can try the following: * Check for calcium build up in the boiler. * Check wiring to all components mentioned. * Inspect if the steam element contactor is locked/on. * Check the B4 boiler temperature probe for defects and ensure B4 probe wires are connected correctly. * Clean the water level probe for calcium build up.
How to fix 'E51 - No Water In Boiler' error in my Alto-Shaam CT PROFORMANCE CTP6-10E?
If your Alto-Shaam oven displays the 'e51 - No Water In Boiler' error, you should: * Check if the water supply is shut off. * Check for low water pressure. * Check if the boiler drain cap is missing. * Inspect the boiler drain pump and check for leaks in the drain pump elbow. * Clean the water level probe for calcium buildup. * Inspect the double water solenoid valve (Y1). * Inspect the relay board for high voltage issues.
What does 'E11 - Convection Temperature High' mean on my Alto-Shaam CT PROFORMANCE CTP6-10E?
If your Alto-Shaam oven displays error 'E11 - Convection Temperature High', you should: * Check wiring to all components mentioned. * Inspect if the steam element contactor is locked/on. * Check the N6 oven cavity temperature probe for defects and ensure its wires are connected correctly. * Inspect the relay board for high voltage issues.
General| Model | CT PROFORMANCE CTP6-10E |
|---|---|
| Category | Oven |
| Power Supply | Electric |
| Control Type | Digital |
| Construction | Stainless Steel |
| Features | programmable touchscreen controls |
