Anyview A8 - Page 271

To Next Page

To Previous Page

Patient monitor User’s manual

Speaker

Gives audible alarm and QRS tone.

Alarm tones meet the requirement of IEC 60601-1-8.

Alarm pressure

45dB to 85dB

，

tested 1meter from the sound

 Connector

Connecting to the host

monitor

1 cable connector

Main Page

Default Chapter1
- Product Information1
- Revision History1
- About this Manual2
- Table of Contents4
Chapter 1 General Introduction11
- Intended Use11
- Main Unit12
- Measurement Modules25
- Equipment Symbols27
Chapter 2 Safety29
- Safety Information29
- General Safety31
- Important Notes for Safety33
- Safe Operation Conditions35
Chapter 3 Basic Operations36
- Unpacking and Checking36
- Getting Started37
- Starting Monitoring38
- Shutting off the Monitor38
- Standby Mode38
- Networked Monitoring39
- Operation Mode39
- Screen Display40
- Using the Smartkeys41
- Setting Measurement Modules43
- Using Mouse45
- Using Soft Keyboard46
- Using SD Memory Card46
- General Setting47
Chapter 4 User Interface50
- Display Style50
- Main Screen Select51
Chapter 5 Alarm61
- Alarm Category61
- Alarm Level61
- Alarm Indicators62
- Alarm Status Symbol64
- Setting Alarm Volume64
- Parameter Alarm64
- Silence66
- Pausing Alarms66
- Acknowledging Alarms67
- Latching Alarms67
- When an Alarm Occurs67
Chapter 6 Patient Management69
- Admitting a Patient69
- Quick Admitting a Patient70
- Edit Patient Information70
- Discharging a Patient71
- Transfer a Patient with EMS71
Chapter 7 ECG74
- Introduction74
- Safety Information74
- Monitoring Procedure75
- ECG Display80
- Setting ECG81
- ST Monitoring82
- Arrhythmia Monitoring86
- Qt/Qtc Interval Monitoring89
Chapter 8 Respiration Rate (Resp)92
- Introduction92
- Safety Information92
- Monitoring Procedure92
- Resp Display93
- Setting Resp94
Chapter 9 Spo295
- Introduction95
- Safety Information95
- Spo Display98
- Setting Spo101
- Measurement Limitations103
- Masimo Information105
- Nellcor Information105
Chapter 10 Temperature (Temp)106
- Introduction106
- Safety Information106
- Monitoring Procedure107
- Temp Display108
- Setting TD108
Chapter 11 NIBP109
- Introduction109
- Safety Information109
- Measurement Limitations110
- Measurement Mode110
- Monitoring Procedure110
- NIBP Display112
- Setting NIBP113
- NIBP Maintenance113
Chapter 12 IBP114
- Introduction114
- Safety Information114
- Monitoring Procedure114
- IBP Display116
- Setting IBP116
- Calculating Cerebral Perfusion Pressure117
- Zeroing the Pressure Transducer118
- Pressure Calibration118
Chapter 13 Carbon Dioxide (CO2)119
- Introduction119
- Monitoring Procedure119
- CO Display124
- Setting CO2125
- Zeroing126
- Calibration127
- Removing Exhaust Gases from the System128
- Safety Information128
Chapter 14 Anesthetic Gas (AG)130
- Introduction130
- Monitoring Procedure131
- AG Display134
- Setting Gas Parameter135
- MAC Calculation135
- Safety Information136
- AG Maintenance139
- Adverse Effects on Performance141
- PHASEIN Information142
Chapter 15 ICG143
- Introduction143
- Calculated Parameters143
- Safety Information145
- Monitoring Procedure146
- ICG Parameter147
- ICG Display148
- Setting ICG Parameter148
- Measurement Limitation148
Chapter 16 C.O150
- Overview150
- Safety Information150
- Display150
- Measurement of C.O151
- Setting152
- Measurement Restrictions156
- Influencing Factors156
Chapter 17 CSM157
- Introduction157
- Safety Information158
- Monitoring Procedure158
- CSM Display161
- Setting CSM163
- Maintenance164
Chapter 18 BIS165
- Overview165
- Safety Information165
- Monitoring Procedure166
- BIS Display166
- BIS Setting169
Chapter 19 EMS172
- Appearance and Structure172
- Operation Mode174
- Basic Operation176
- User's Screen180
- Parameter Measurement184
- Alarm196
- Reviewing198
Chapter 20 Freezing201
- Freezing Waveform201
- Reviewing Waveform201
- Releasing Freezing202
Chapter 21 Reviewing203
- Reviewing Graphic Trends203
- Reviewing Tabular Trends204
- Reviewing NIBP Measurement Results205
- Reviewing Parameter Alarm206
- Reviewing Holographic Waveform207
Chapter 22 Calculations209
- Drug Dose Calculation209
- Hemodynamic Calculation210
- Nephridium Calculation212
- Ventilation Calculation214
- Oxygenation Calculation215
- NIBP Analyze217
- HRV Analyze218
Chapter 23 Other Functions221
- Nurse Call221
- Analog Signal Output221
Chapter 24 Recording222
- Recorder222
- Recording Type222
- Setting Recorder223
- Starting and Stopping Recording224
- Installing Recording Paper224
- Clearing Jam Paper225
- Cleaning Recorder225
Chapter 25 Battery226
- Introduction226
- Installing a Battery227
- Optimizing Battery Performance227
- Checking Battery Performance228
- Disposing Batteries228
Chapter 26 Maintenance and Cleaning229
- Equipment Maintenance229
- Equipment Cleaning230
- Cleaning of the Monitor230
- Cleaning of EMS231
- Cleaning and Sterilizing of Accessories231
Chapter 27 Accessories235
Appendix A Product Specifications240
- Safety Specifications240
- Environmental Specifications241
- Physical Specifications241
- Hardware Specifications242
- Measurement Specifications247
- EMS Specifications269
Appendix B Factory Defaults272
- Monitor Defaults272
- EMS Defaults282
Appendix C Alarm Messages286
- Monitor Alarm Messages286
- EMS Alarm Messages296

Anyview A8 - Page 271

Table of Contents

Related product manuals