DS7240-UK Reference Guide Copyright 2003 Bosch Security Systems P/N: 4998122677Cr1 Page 3
Contents
Part I: Introduction ..............................................................7
1.0 Specifications ........................................................7
1.1 Environmental Specifcations...............................7
1.2 Voltage Input......................................................7
1.3 Power Outputs ...................................................7
1.4 Minimum Operating Voltage................................7
1.5 Data Bus...........................................................7
1.6 Keypads.............................................................7
2.0 Standard Features .................................................7
2.1 Communicator....................................................7
2.2 Zones ................................................................7
2.3 Areas and Accounts ...........................................7
2.4 Programmable Outputs ......................................7
2.5 Users.................................................................7
2.6 Keyswitch/Exit Terminator ..................................7
2.7 Alarm Event Memory..........................................7
2.8 History Log ........................................................8
2.9 Wireless (RF) Devices........................................8
2.10 Programming .....................................................8
3.0 Panel Assembly.....................................................8
4.0 Listings and Approvals ...........................................8
5.0 System Options .....................................................8
5.1 Arming Devices..................................................8
5.2 Data Bus Devices...............................................8
5.3 RF Devices ........................................................8
5.4 Programming Tools............................................8
6.0 Standby Battery .....................................................9
7.0 Available Power .....................................................9
7.1 Auxiliary Power ..................................................9
7.2 Alarm Power ......................................................9
7.3 Installer Keypad Connector.................................9
Part II: System Installation and Setup.................................9
8.0 Panel Installation ...................................................9
8.1 Electro Magnetic Interference (EMI)....................9
8.2 Enclosure Mounting..........................................10
8.3 Standby Battery Installation ..............................10
9.0 Telephone Connections .......................................11
10.0 Arming Device Installation ....................................11
10.1 Keypad Addressing..........................................11
10.2 Keypad Installation...........................................11
10.3 Keyswitch ........................................................12
11.0 On-board Sensor Loop Setup...............................13
11.1 Overview..........................................................13
11.2 Tamper-wired Zone Configuration.....................13
11.3 No EOL Zone Configuration..............................13
11.4 Four-wire Smoke Detector Configuration...........13
12.0 On-board Output Setup........................................13
12.1 Overview..........................................................13
12.2 Programmable Output 1 (PO 1) ........................14
12.3 Programmable Outputs 2-4 (PO 2- PO 4)..........14
13.0 RF3227E RF Receiver Setup ...............................15
13.1 RF Receiver Addressing...................................15
13.2 RF3227E Installation........................................15
13.3 RF3227E Programming....................................15
14.0 Off-board Sensor Loops (DX2010)........................15
14.1 DX2010 (DX2013/DX2014) Overview................15
14.2 DX2010 Installation..........................................15
14.3 DX2010 to Panel Data Bus Connections...........16
14.4 DX2010 Auxiliary Output Connections...............17
14.5 DX2010 Tamper Input Connections ..................18
14.6 DX2010 Tamper-wired Configuration................18
14.7 DX2010 Addressing .........................................18
14.8 DX2010 Status LED .........................................19
15.0 Off-board Outputs (DX3010).................................19
15.1 Overview..........................................................19
15.2 DX3010 Configuration......................................19
15.3 DX3010 Relay Outputs.....................................19
15.4 DX3013 Installation..........................................20
15.5 DX3010 to Panel Data Bus Connections...........21
15.6 DX3010 Address Programming ........................22
16.0 RS-232 Serial Interface (DX4010) ........................22
16.1 DX4010 Overview ............................................22
16.2 DX4010 Installation..........................................22
16.3 DX4010 Remote Programming Direct Connect..23
16.4 DX4010 Configuration Jumpers........................24
16.5 DX4010 Addressing .........................................24
16.6 DX4010 Supervision.........................................24
16.7 DX4010 DB9 Connector...................................24
17.0 Power Up ............................................................25
18.0 System Status LED..............................................25
19.0 Installer Keypad...................................................26
20.0 Installer Mode......................................................26
20.1 Entering Installer Mode.....................................26
21.0 Installer Menu......................................................26
21.1 Bell Test ..........................................................26
21.2 Strobe Test......................................................26
21.3 Battery Test .....................................................26
21.4 Test Report......................................................26
21.5 Zone Status .....................................................26
21.6 Output Test......................................................27
21.7 RF Menu..........................................................27
21.8 Keypad Program (How to Program)..................28
21.9 Programming Key (PK32).................................30
21.10 Exiting the Installer Menu..............................30
21.11 Always Force Arm ........................................30
Part III: Panel Programming..............................................31
22.0 Programming Tables............................................31
23.0 Routing Destinations............................................32
23.1 Phone Number 1 (2) for Destination 1 (2)..........32
23.2 Format for Destination 1 (2)..............................33
24.0 Phone, Auto-Forward and RPS Configuration .......34
24.1 Phone Line Options..........................................34
24.2 DTMF/Pulse Dialing .........................................34
24.3 Call Forwarding Auto On/Off Digits/Call Barring.35
24.4 Remote Programming Call Back Number..........35
24.5 RPS Answer Ring Count, Answer Machine
Bypass ............................................................36
24.6 Phone Line Fault Response Options.................37
25.0 Global Reporting Options.....................................38
25.1 Global Reporting Options .................................38
25.2 Ack Wait Time..................................................39
25.3 AC Power Supervision Options.........................39
25.4 AC Fail [1], Low Battery [22] Report Options .....40
25.5 System Status Report Swinger Count ...............40
25.6 System Status Reports Routing........................41
25.7 Call for Service Interval ....................................41
25.8 System Inactive Interval ...................................41
25.9 Call for Service/System Inactive Options...........42
25.10 Log Supervision Configuration ......................43
25.11 Auto On Pre-Alert Time ................................43
25.12 Cancel Event Enabled ..................................44
25.13 Date Format and Enable PIN Trouble............44
25.14 Daylight Saving Calendar .............................45
25.15 Daylight Saving Clock Advance Hour............45
25.16 Daylight Saving Clock Reverse Hour.............45
25.17 AC Fail Report Delay....................................46
To Next Page
