Bosch DS7240-UK - Page 5

DS7240-UK Reference Guide Copyright  2003 Bosch Security Systems P/N: 4998122677Cr1 Page 5
45.0 RF Keyfobs........................................................129
45.1 RF Keyfob Receiver Assignment Options........129
45.2 RF Keyfob Options.........................................130
46.0 Factory Default ..................................................130
47.0 Tamper Response Configuration ........................131
47.1 Tamper Alarm/Trouble Options.......................131
47.2 System Alarm Reports/Output Options............132
48.0 Exit Delay Configuration.....................................132
48.1 Contact Set/Exit Delay Cancel Zone Options...132
48.2 Exit Terminator Zone Options.........................133
48.3 Panel Arming Options.....................................134
48.4 Confirmation Alarm Timer...............................135
49.0 Reporting Format Configuration..........................136
49.1 Personal Dialing Format Configuration............136
49.2 BSIA Fast Format Configuration .....................137
49.3 Basic Pager Display.......................................138
Part IV: Reference Materials............................................141
50.0 Troubleshooting.................................................141
50.1 Arming Issues ................................................141
50.2 Zone Issues ...................................................141
50.3 Programming Issues.......................................142
50.4 Keypad Issues ...............................................143
50.5 Miscellaneous Issues .....................................143
51.0 Data Bus Address Quick Reference....................143
52.0 BSIA Fast Format ..............................................144
53.0 SIA 300 with Text Blocks....................................144
54.0 Personal Dialing Format.....................................145
55.0 Dialing Attempt Tables .......................................146
55.1 Destination 1 Only..........................................146
55.2 Destination 2 Only..........................................146
55.3 Destination 1 and Destination 2 ......................147
56.0 Call for Service Details.......................................148
57.0 Keypad Quick Reference....................................149
57.1 System Arming/Disarming Functions...............149
57.2 Other System Functions.................................149
58.0 History Log ........................................................150
59.0 Panel Events and Reporting Formats..................151
60.0 Glossary............................................................161
Figures
Figure 1: Panel Wiring Connections.......................................1
Figure 2: Enclosure Mounting..............................................10
Figure 3: Battery Connections .............................................10
Figure 4: Telephone Connections ........................................11
Figure 5: Jumper Plug Configuration....................................11
Figure 6: Wiring a Keypad to the Panel ................................11
Figure 7: Keypad External Power Supply Connections .........12
Figure 8: Keyswitch Wiring ..................................................12
Figure 9: Tamper-Wired Zone Wiring ...................................13
Figure 10: Single Zone Sensor Loop Wiring (No EOL)..........13
Figure 11: Typical 4-wire Smoke Detector Wiring .................13
Figure 12: PO 1 Wiring........................................................14
Figure 13: PO 2 – PO 4 Wiring ............................................14
Figure 14: RF3227E Address Jumper Settings.....................15
Figure 15: RF3227E to Panel Connections...........................15
Figure 16: DX2013 Mounting Locations ...............................15
Figure 17: Mounting the DX2013 (Step 1) ............................16
Figure 18: Mounting the DX2013 (Step 2) ............................16
Figure 19: Mounting the DX2013 (Step 3) ............................16
Figure 20: DX2010 to Panel Connections.............................17
Figure 21: External Power Supply Connections....................17
Figure 22: DX2010 Auxiliary Output Connections.................17
Figure 23: DX2010 Tamper Input Wiring..............................18
Figure 24: DX2010 Wire Jumper Connections......................18
Figure 25: DX2010 Tamper-Wired Loop Configuration .........18
Figure 26: DX2010 DIP Switch Configuration.......................19
Figure 27: DX2010 Status LED Location..............................19
Figure 28: DX3013 Mounting Locations ...............................20
Figure 29: Mounting the DX3013 (Step 1) ............................20
Figure 30: Mounting the DX3013 (Step 2) ............................20
Figure 31: Mounting the DX3013 (Step 3) ............................21
Figure 32: Wiring the DX3010 to the Panel...........................21
Figure 33: DX3010 External Power Supply Connections.......21
Figure 34: DX3010 DIP Switch Configuration.......................22
Figure 35: DX4010 PCB......................................................22
Figure 36: DX4010 to Panel Connections.............................23
Figure 37: DX4010 External Power Supply Connections.......23
Figure 38: Direct Connect DIP Switch Setting.......................23
Figure 39: Remote Programming Direct Connection.............23
Figure 40: DX4010 P2 Jumper Pin Settings .........................24
Figure 41: DX4010 P3 Jumper Pin Settings .........................24
Figure 42: RS-232 Device DIP Switch Setting ......................24
Figure 43: DX4010 DB9 Connector Layout...........................24
Figure 44: Panel Reset Display............................................25
Figure 45: System Status LED.............................................25
Figure 46: Installer Keypad Connections..............................26
Figure 47: Adding RF ID Codes Menu Display .....................27
Figure 48: RF ID Code Display............................................27
Figure 49: Test RF Devices Display.....................................27
Figure 50: RF Device Test Status Display............................27
Figure 51: RF ID Code Entry Display ...................................28
Figure 52: Initial Programming Display.................................28
Figure 53: Selecting an Address..........................................28
Figure 54: Editing Data Digits ..............................................29
Figure 55: Reset Display Screen..........................................29
Figure 56: PK32 to Panel Connections.................................30
Figure 57: Sample Programming Entry ................................31
Figure 58: Routing Destinations...........................................32
Figure 59: History Log Display...........................................150