Bosch Solution 16i User Guide

11
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16 i User Guide
System Pro gramming
i
Note
To enter programming mode simply enter your PIN
and press the MENU key on the keypad.
The default Master user PIN is 2580.
Access > PIN Codes >
dEL-Ur
Erase User
MENU 1-0-0
This command allows a master user to to erase another
user from the system. Erasing a user will remove the user’s
PIN, Proximity Token and RF keyfob credentials.
1. Ensure that the system (or area) is turned o.
2. Enter Master PIN + [MENU]
3. Enter [1] + [0] + [0] + [OK].
The keypad will display Ur = prompting you to enter
the number of the user to erase.
Ur=
4. Enter the user number then press [OK].
dEL ?
5. The keypad will now prompt you to conrm the
erasure by pressing [OK].
Access > PIN Codes >
ch-PiN
Change Own PIN
MENU 1-1-0
This menu lets you change your own PIN. It is recommended
that you write down your old PIN and the new one before
you begin. The new PIN must have the same number of
digits as your old PIN unless the variable PIN length option
has programmed by your installer. Once the change is
complete you should destroy the written copy.
At factory default, each PIN is xed to 4 digits in length.
1. Enter your PIN + [MENU]
2. Enter [1] + [1] + [0] + [OK].
The keypad will prompt you to enter a new PIN.
EntPin
3. Enter your new PIN, and then press [OK].
If an error tone sounds and the display reads “bAdPin”
you should try a dierent PIN. The keypad will now
prompt you to enter your new PIN again.
rEPEAT
4. To conrm your new PIN, enter your new PIN again.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving. Your PIN has now been changed.
Access > PIN Codes >
ch-Oth
Change Other PIN
MENU 1-1-1
This menu allows a master user to change somebody else’s
PIN. It is recommended that you write down the old PIN
and the new one before you begin. Once the change is
complete you should destroy the written copy. The new
PIN must have the same number of digits as the old PIN.
At factory default, each PIN is xed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580.
1. Enter your master PIN + [MENU]
2. Enter [1] + [1] + [1] + [OK].
The keypad will display Ur = prompting you to enter the
number of the user to change. Each user in the system
is assigned a user number as well as a PIN Number.
Ur=
3. Enter the user number to change then press [OK].
EntPin
4. Enter the new PIN.
If an error tone sounds, or “bAdPin” is displayed try a
dierent PIN.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > PIN Codes >
AddPin
Add PIN
MENU 1-1-2
This menu allows a master user to add a PIN for a new user.
Each master user can only program new PINs for those
users that have been assigned to the same area(s) as the
master user.
At factory default, each PIN is xed to 4 digits in length
however this can be changed by your installer to suit your
needs. The default PIN for User 1 (Master user) is 2580.
1. Enter your master PIN + [MENU]
2. Enter [1] + [1] + [2] + [OK].
The keypad will display the Ur = prompt.

Bosch Solution 16i Specifications

General

Brand	Bosch
Model	Solution 16i
Category	Security System
Language	English