Cimbali M26 - Page 75

English
29 EN
Messages in explicit mode
MESSAGE POSSIBLE CAUSES: when the message is
visualized
VERIFICATIONS
Machine cold
Please wait
This message will appear on the display if any
dispensing icon is pressed every time the machine
is turned on until the service boiler pressure falls
below the pre-set working pressure.
When the service boiler reaches the pre-set
pressure, the message automatically disappears.
Service needed This message is displayed when the machine
requires the periodic maintenance intervention. In
order to eliminate temporary the message, keep
pressed key for approximately 8 seconds. The
message will reappears in the successive relighting
of the machine with the main switch.
Contact the authorized technical department. The
message will be displayed until the service will be
carried out.
Softener This message is displayed when the softener resins
need to be regenerated. (Follow the instructions on
softener maintenance).
Once regeneration has been completed, keep the
key pressed for approximately 8 seconds to
cancel out the message.
Change water
¿OWHU
This message is displayed when the machine
reqXLUHVWKHVXEVWLWXWLRQRIWKHZDWHU¿OWHU.
In order to eliminate temporary the message, keep
pressed key for approximately 8 seconds. The
message will appear again at regular intervals.
Contact an authorised technician. The message
wiOOEHGLVSOD\HGXQWLOWKH¿OWHUKDVEHHQUHSODFHG
Note: the need to WRUHSODFHWKH¿OWHULVUHFRUGHG
by the machine.
Machine in
stand-by
This message is displayed when the machine
switch ON/OFF has been programmed. The
PHVVDJHLQGLFDWHVWKDWWKHPDFKLQHLVVZLWFKRႇ
and is in stand-by status.
Refer to the Technician’s Manual to see how to pro-
gram the switch ON/OFF of the machine.
Press any dispensing button to force the machine
on.
Energy saving
mode
This message is displayed when the machine is in
ECONOMY mode.
Press any dispensing button to exit the ECONOMY
mode and return to the machine work phase.
Messages
about washings
Please consult this manual at the "Cleaning op-
erations ".
Direct action by the customer
Before calling service personnel, to avoid unnecessary expense, check whether the machine problem corresponds to
one of the cases listed below.
19. Defects - Malfunctions
PROBLEM CAUSE SOLUTION
7KH FRႇHH PDFKLQH GRHV QRW ZRUN
and the display (16) is blank.
No electricity supply. Check the electricity supply.
Check the position of the main switch
(1).
/HDNLQJIURPWKH¿OWHUKROGHUULP21). 8QGHUSDQJDVNHWGLUW\ZLWKFRႇHH Clean using the special brush provided.
&RႇHHGLVSHQVLQJWLPHWRRVKRUW &RႇHHJURXQGWRRFRDUVH
&RႇHHWRRROG
8VHD¿QHUJULQG
8VHQHZFRႇHH
&RႇHHGULSVRXWRIPDFKLQH Filter holes blocked or filter holder
(21) outlet hole dirty.
&RႇHHJURXQGWRR¿QH
Clean.
Use a coarser grind.
Loss of water under the machine. Discharge well clogged up.
Discharge basin hole blocked.
Clean.
Clean.
Machine heated up, but it does not
GLVSHQVHFRႇHH
Water supply or water softener tap
closed.
No water in system.
Open the taps
Wait until water is available or call a
plumber.
The automatic level-control devices
remain in operation.
Same causes as above. Same solution as above.
02_M26_UNICO_EU_2314.indd 29
02_M26_UNICO_EU_2314.indd 29
07/04/2023 12:05:45
07/04/2023 12:05:45