EasyManuals Logo

Cisco 2800 Series User Manual

Cisco 2800 Series
266 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #172 background imageLoading...
Page #172 background image
Hoot and Holler over V3PN Configuration Example
Verify
32
OL-6573-01
PIM Group-to-RP Mappings
Group(s) 224.0.0.0/4
RP 192.168.4.1 (?), v2v1
Info source: 192.168.4.1 (?), elected via Auto-RP
Uptime: 00:20:28, expires: 00:02:23
The following is an output example for the show ip mroute active command, performed using the
configuration on the Branch 1 router:
Branch-1# show ip mroute active
Active IP Multicast Sources - sending >= 4 kbps
Group: 239.168.1.100, (?)
Source: 192.168.5.2 (?)
Rate: 0 pps/0 kbps(1sec), 80 kbps(last 10 secs), 7 kbps(life avg)
Source: 192.168.7.2 (?)
Rate: 0 pps/0 kbps(1sec), 80 kbps(last 10 secs), 7 kbps(life avg)
The following is an output example for the show voice trunk-conditioning supervisory command,
performed using the configuration on the Branch 1 router:
Branch-1# show voice trunk-conditioning supervisory
SLOW SCAN
1/0 : state : TRUNK_SC_CONNECT, voice : on, signal : on ,master
status: trunk connected
sequence oos : no-action
pattern :
timing : idle = 0, restart = 0, standby = 0, timeout = 65535
supp_all = 0, supp_voice = 0, keep_alive = 0
timer: oos_ais_timer = 0, timer = 0
The following is an output example for the show voip rtp connections command, performed using the
configuration on the Branch 1 router:
Branch-1# show voip rtp connections
VoIP RTP active connections :
No. CallId dstCallId LocalRTP RmtRTP LocalIP RemoteIP
1 4 3 31156 19890 192.168.7.2 239.168.1.100
Found 1 active RTP connections
The following is an output example for the show voice call summary command, performed using the
configuration on the Branch 1 router:
Branch-1# show voice call summary
PORT CODEC VAD VTSP STATE VPM STATE
============== ======== === ==================== ======================
1/0 g711ulaw y S_CONNECT S_TRUNKED
1/1 - - - FXSLS_ONHOOK
1/2 - - - FXSLS_ONHOOK
1/3 - - - FXSLS_ONHOOK
The following is an output example for the show class map command, performed using the
configuration on the Branch 1 router:
Branch-1# show class-map
Class Map match-all control-traffic (id 1)
Match ip dscp af31

Table of Contents

Other manuals for Cisco 2800 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 2800 Series and is the answer not in the manual?

Cisco 2800 Series Specifications

General IconGeneral
Power SupplyInternal power supply
Product TypeRouter
Form FactorRack-mountable
Connectivity TechnologyWired
Power DeviceInternal power supply
Operating SystemCisco IOS
Integrated ServicesSecurity, voice
WAN InterfacesT1/E1, Serial
LAN InterfacesFast Ethernet, Gigabit Ethernet
Expansion Slots4
Data Link ProtocolEthernet, Fast Ethernet, Gigabit Ethernet
Network/Transport ProtocolIP, TCP
Remote Management ProtocolSNMP, Telnet
FeaturesVPN support, Quality of Service (QoS), VLAN support
Voltage RequiredAC 100-240 V
Security FeaturesFirewall, VPN, Access Control Lists (ACLs)

Related product manuals