EasyManuals Logo

Cisco 2800 Series User Manual

Cisco 2800 Series
266 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #30 background imageLoading...
Page #30 background image
14
Basic Software Configuration Using the Setup Command Facility
OL-5992-01
Examples of Using the Setup Command Facility to Configure Interface Parameters
The following is a sample configuration for ISDN basic rate communication:
BRI interface needs isdn switch-type to be configured
Valid switch types are:
[0] none..........Only if you don't want to configure BRI.
[1] basic-1tr6....1TR6 switch type for Germany
[2] basic-5ess....AT&T 5ESS switch type for the US/Canada
[3] basic-dms100..Northern DMS-100 switch type for US/Canada
[4] basic-net3....NET3 switch type for UK and Europe
[5] basic-ni......National ISDN switch type
[6] basic-ts013...TS013 switch type for Australia
[7] ntt...........NTT switch type for Japan
[8] vn3...........VN3 and VN4 switch types for France
Choose ISDN BRI Switch Type [2]:
Do you want to configure BRI0/0/0 interface? [yes]:
Some encapsulations supported are
ppp/hdlc/frame-relay/lapb/x25
Choose encapsulation type [ppp]:
Note
The following sections describe the prompts for each encapsulation type. No further configuration is
needed for HDLC encapsulation.
Do you have service profile identifiers (SPIDs) assigned? [no]: y
Enter SPID1: 12345
Enter SPID2: 12345
Note
The setup command facility prompts you for the service profile identifier (SPID) number only if you
specify basic-5ess, basic-ni1, or basic-dms100 for the switch type.
Do you want to map the remote machine's IP address in dialer map? [yes]:
IP address for the remote interface: 192.0.0.1
Do you want to map the remote machine's IP address in dialer map? [yes]:
IPX address of the remote interface: 40.0060.34c6.90ed
To get to 192.0.0.1 we will need to make a phone call.
Please enter the phone number to call: 1234567890
Configure IP on this interface? [yes]:
Note
If your router has at least one configured LAN interface, you can choose to use an unnumbered IP
address on the interface.
Configure IP unnumbered on this interface? [no]: y
Assign to which interface [Ethernet0/0]:
New Zealand basic-nznet3 New Zealand NET3 switches
North America basic-5ess AT&T basic rate switches
basic-dms100 NT DMS-100 basic rate switches
basic-ni1 National ISDN-1 switches
Table 1 ISDN Switch Types (continued)
Country ISDN Switch Type Description

Table of Contents

Other manuals for Cisco 2800 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 2800 Series and is the answer not in the manual?

Cisco 2800 Series Specifications

General IconGeneral
Power SupplyInternal power supply
Product TypeRouter
Form FactorRack-mountable
Connectivity TechnologyWired
Power DeviceInternal power supply
Operating SystemCisco IOS
Integrated ServicesSecurity, voice
WAN InterfacesT1/E1, Serial
LAN InterfacesFast Ethernet, Gigabit Ethernet
Expansion Slots4
Data Link ProtocolEthernet, Fast Ethernet, Gigabit Ethernet
Network/Transport ProtocolIP, TCP
Remote Management ProtocolSNMP, Telnet
FeaturesVPN support, Quality of Service (QoS), VLAN support
Voltage RequiredAC 100-240 V
Security FeaturesFirewall, VPN, Access Control Lists (ACLs)

Related product manuals