EasyManua.ls Logo

Cisco ASR1002 - ASR 1002 Router - Page 303

Cisco ASR1002 - ASR 1002 Router
462 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Configuring Call Home
Message Contents
47
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled
No active filter modules.
Trap logging: level informational, 104 message lines logged
Log Buffer (1000000 bytes):
*Dec 3 07:16:55.020: ASR1000-RP HA: RF status CID 1340, seq 93, status
RF_STATUS
_REDUNDANCY_MODE_CHANGE, op 0, state DISABLED, peer DISABLED
*Dec 3 07:17:00.379: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf
created w
ith ID 4085, ipv4 table-id 0xFF5, ipv6 table-id 0x1E000001
*Dec 3 07:17:00.398: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available.
The netwo
rk clock has changed to freerun
*Dec 3 07:17:00.544: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0, changed
state to
up
*Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface EOBC0, changed state to up
*Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up
*Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface LIIN0, changed state to up
*Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down
*Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state
to up
*Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed
state to
up
*Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state
to up
*Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0,
changed s
tate to down
*Dec 3 07:17:01.818: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded
from the
Shell Manager
*Dec 3 07:16:30.926: %CMRP-5-PRERELEASE_HARDWARE: R0/0: cmand: 2 is pre-release hardware
*Dec 3 07:16:24.147: %HW_IDPROM_ENVMON-3-HW_IDPROM_CHECKSUM_INVALID: F1: cman_fp: The
idprom co
ntains an invalid checksum in a sensor entry. Expected: 63, calculated: fe
*Dec 3 07:16:24.176: %CMFP-3-IDPROM_SENSOR: F1: cman_fp: One or more sensor fields from
the idpro
m failed to parse properly because Success.
*Dec 3 07:16:27.669: %CPPHA-7-START: F1: cpp_ha: CPP 0 preparing image
/tmp/sw/f
p/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
*Dec 3 07:16:27.839: %CPPHA-7-START: F1: cpp_ha: CPP 0 startup init image
/tmp/sw/f
p/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
*Dec 3 07:16:28.659: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image
/tmp/sw/f
p/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
*Dec 3 07:16:28.799: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image
/tmp/sw/f
p/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
*Dec 3 07:16:32.557: %CPPHA-7-START: F1: cpp_ha: CPP 0 running init image
/tmp/sw/f
p/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
*Dec 3 07:16:32.812: %CPPHA-7-READY: F1: cpp_ha: CPP 0 loading and initialization
complete
*Dec 3 07:16:33.532: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image
/tmp/sw/f
p/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
*Dec 3 07:16:33.786: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization
complete
*Dec 3 07:16:34.158: %IOSXE-6-PLATFORM: F1: cpp_cp: Process
CPP_PFILT
ER_EA_EVENT__API_CALL__REGISTER
*Dec 3 07:16:35.134: %IOSXE-6-PLATFORM: F0: cpp_cp: Process
CPP_PFILT
ER_EA_EVENT__API_CALL__REGISTER
*Dec 3 07:16:38.965: %CMRP-6-FP_HA_STATUS: R0/0: cmand: F0 redundancy state is Active
with read
y Standby
*Dec 3 07:17:01.926: %DYNCMD-7-PKGINT_INSTALLED: The command package 'platform_trace' has
been succ
esfully installed

Table of Contents

Other manuals for Cisco ASR1002 - ASR 1002 Router

Related product manuals