Configuring Call Home
Message Contents
49
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
*Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS0/2/6, changed state to down
*Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS0/2/7, changed state to down
*Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS2/3/0, changed state to down
*Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS1/3/0, changed state to down
*Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/0,
changed s
tate to down
*Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/1,
changed s
tate to down
*Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/2,
changed s
tate to down
*Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/3,
changed s
tate to down
*Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/4,
changed s
tate to down
*Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/5,
changed s
tate to down
*Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/6,
changed s
tate to down
*Dec 3 12:17:14.755 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/7,
changed s
tate to down
*Dec 3 12:17:14.848 IST: %SONET-4-ALARM: POS0/2/1: SLOS declared
*Dec 3 12:17:14.848 IST: %SONET-4-ALARM: POS0/2/2: SLOS declared
*Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/3: SLOS declared
*Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/4: SLOS declared
*Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/5: SLOS declared
*Dec 3 12:17:14.850 IST: %SONET-4-ALARM: POS0/2/6: SLOS declared
*Dec 3 12:17:14.850 IST: %SONET-4-ALARM: POS0/2/7: SLOS declared
*Dec 3 12:17:14.850 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/3/0,
changed s
tate to down
*Dec 3 12:17:14.851 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS1/3/0,
changed s
tate to down
*Dec 3 12:17:16.069 IST: %LINK-3-UPDOWN: Interface POS0/2/0, changed state to up
*Dec 3 12:17:15.734 IST: %LINK-3-UPDOWN: SIP0/2: Interface POS0/2/0, changed state to up
*Dec 3 12:17:16.868 IST: %LINK-3-UPDOWN: Interface POS1/3/0, changed state to up
*Dec 3 12:17:16.905 IST: %LINK-3-UPDOWN: Interface POS2/3/0, changed state to up
*Dec 3 12:17:16.538 IST: %LINK-3-UPDOWN: SIP0/2: Interface POS0/2/7, changed state to
down
*Dec 3 12:17:17.070 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/0,
changed s
tate to up
*Dec 3 12:17:16.488 IST: %LINK-3-UPDOWN: SIP1/3: Interface POS1/3/0, changed state to up
*Dec 3 12:17:17.868 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS1/3/0,
changed s
tate to up
*Dec 3 12:17:16.199 IST: %LINK-3-UPDOWN: SIP2/3: Interface POS2/3/0, changed state to up
*Dec 3 12:17:17.905 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/3/0,
changed s
tate to up
*Dec 3 12:22:01.574 IST: %IP-4-DUPADDR: Duplicate address 172.27.55.233 on
GigabitEt
hernet0, sourced by 001a.3044.1ec0
*Dec 3 12:23:47.613 IST: %SYS-5-CONFIG_I: Configured from console by console
*Dec 3 12:24:37.134 IST: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console
*Dec 3 12:25:34.356 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has
failed. E
rror code = 0x1 (DIAG_FAILURE)
*Dec 3 12:25:39.459 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has
failed. E
rror code = 0x1 (DIAG_FAILURE)
*Dec 3 12:25:54.405 IST: %SYS-5-CONFIG_I: Configured from console by console
mcp-6ru-3#
Command Output Name : show inventory
Attachment Type : command output
MIME Type : text/plain
Command Output Text : NAME: "Chassis", DESCR: "Cisco ASR1006 Chassis"
PID: ASR1006 , VID: V00, SN: FOX105101DH
NAME: "module 0", DESCR: "Cisco ASR1000 SPA Interface Processor 10"
PID: MCP-CC , VID: V00, SN: JAB1104064W
To Next Page
Loading...
