EasyManua.ls Logo

Cisco ASR1002 - ASR 1002 Router - Page 91

Cisco ASR1002 - ASR 1002 Router
462 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Software Upgrade Process
ISSU Upgrade for Redundant Platforms
9
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Examples
The following example shows how to perfrom consolidated package upgrade in a dual route processor
configuration:
Router(config)# ip tftp source-interface gigabitethernet 0
Router# c
opy tftp bootflash:
Address or name of remote host []? 172.17.16.81
Source filename []?
/auto/tft
p-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin
Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]?
Accessing
tftp://17
2.17.16.81//auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.
bin...
Loading /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin from
172.17.16
.81 (via GigabitEthernet0):
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!
[OK - 209227980 bytes]
209227980 bytes copied in 329.215 secs (635536 bytes/sec)
Router# c
opy bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin stby-bootflash:
Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]?
Step 21
show version
show version active-RP running
show version active-RP provisioned
show platform
show running-configuration
(Optional) Enter the show version, show platform,
or show runnning-configuration commands to
confirm that the upgrade completed successfully, as
follows:
show version—Confirm that the correct
software version is running on your router and
that the RP was booted from the correct file.
show running-configuration—Confirm that
the booting configuration, in particular the boot
system statements, are correct.
Tip Use the show running-config | include boot
command to display only the boot statements
from the show running-configuration
output.
show platform— Confirm that both RP0 and
RP1 are correctly running as active and standby.
Step 22
hw-module slot RP-slot reload
Example:
Router# hw-module slot R0 reload
Reload the new software on the Standby RP.
Command or Action Purpose

Table of Contents

Other manuals for Cisco ASR1002 - ASR 1002 Router

Related product manuals