Cisco ASR1006 - ASR 1006 Modular Expansion Base User Manual

Configuring Call Home
Message Contents
52
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
</aml-block:Content>
<aml-block:Attachments>
<aml-block:Attachment type="inline">
<aml-block:Name>show logging</aml-block:Name>
<aml-block:Data encoding="plain">
<![CDATA[
Syslog logging: enabled (1 messages dropped, 29 messages rate-limited, 0 flushes, 0
overruns,
xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 114 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled
No active filter modules.
Trap logging: level informational, 106 message lines logged
Log Buffer (1000000 bytes):
*Dec 3 07:16:55.020: ASR1000-RP HA: RF status CID 1340, seq 93, status
RF_STATUS
_REDUNDANCY_MODE_CHANGE, op 0, state DISABLED, peer DISABLED
*Dec 3 07:17:00.379: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf
created w
ith ID 4085, ipv4 table-id 0xFF5, ipv6 table-id 0x1E000001
*Dec 3 07:17:00.398: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available.
The netwo
rk clock has changed to freerun
*Dec 3 07:17:00.544: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0, changed
state to
up
*Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface EOBC0, changed state to up
*Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up
*Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface LIIN0, changed state to up
*Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down
*Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state
to up
*Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed
state to
up
*Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state
to up
*Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0,
changed s
tate to down
*Dec 3 07:17:01.818: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded
from the
Shell Manager
*Dec 3 07:16:30.926: %CMRP-5-PRERELEASE_HARDWARE: R0/0: cmand: 2 is pre-release hardware
*Dec 3 07:16:24.147: %HW_IDPROM_ENVMON-3-HW_IDPROM_CHECKSUM_INVALID: F1: cman_fp: The
idprom co
ntains an invalid checksum in a sensor entry. Expected: 63, calculated: fe
*Dec 3 07:16:24.176: %CMFP-3-IDPROM_SENSOR: F1: cman_fp: One or more sensor fields from
the idpro
m failed to parse properly because Success.
*Dec 3 07:16:27.669: %CPPHA-7-START: F1: cpp_ha: CPP 0 preparing image
/tmp/sw/f
p/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
*Dec 3 07:16:27.839: %CPPHA-7-START: F1: cpp_ha: CPP 0 startup init image
/tmp/sw/f
p/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode

Cisco ASR1006 - ASR 1006 Modular Expansion Base Specifications

General

Rack Units	6U
Form Factor	Rack-mountable
Operating Temperature	32 to 104°F (0 to 40°C)
Product Type	Router
Slots	6
Redundancy	Redundant Power Supply Supported
Maximum Throughput	100 Gbps
Dimensions	17.5" Width
Weight	Approximately 130 lbs (59 kg)
Interfaces/Ports	Varies by installed modules
Memory	4 GB
Storage Temperature	-40°F to 158°F (-40°C to 70°C)
Relative Humidity	5% to 95% (noncondensing)
Compliance	CE, UL