Cisco MDS 9000 Series Troubleshooting Guide

Send comments to mdsfeedback-doc@cisco.com.
1-6
Cisco MDS 9000 Family Troubleshooting Guide
OL-5183-02, Cisco MDS SAN-OS Release 1.3
Chapter 1 Troubleshooting Overview
Using Cisco MDS 9000 Family Tools
Dec 10 23:40:26 flogi: current event [FLOGI_EV_NAME_SERVER_REG_RESPONSE]
Dec 10 23:40:26 flogi: next state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: fu_fsm_execute: ([1]21:00:00:e0:8b:08:96:22)
Dec 10 23:40:26 flogi: current state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: current event [FLOGI_EV_ACL_CFG_RESPONSE]
Dec 10 23:40:26 flogi: next state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: current state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: current event [FLOGI_EV_ZS_CFG_RESPONSE]
Dec 10 23:40:26 flogi: next state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: fu_fsm_execute_all: done processing event FLOGI_EV_ZS_CFG_RESPONSE
Dec 10 23:40:26 flogi: current state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: current event [FLOGI_EV_LCP_RESPONSE]
Dec 10 23:40:26 flogi: next state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: fu_fsm_execute: ([1]21:00:00:e0:8b:08:96:22)
Dec 10 23:40:26 flogi: current state [FLOGI_ST_PERFORM_CONFIG]
Dec 10 23:40:26 flogi: current event [FLOGI_EV_CONFIG_DONE_COMPLETE]
Dec 10 23:40:26 flogi: next state [FLOGI_ST_FLOGI_DONE]
The following is a summary of the available debug commands:
Table 1-1 Debug commands
Debug command Purpose
acl Enable acl debugging
all Enable all debugging
ascii-cfg Configure ascii-cfg debugging
bootvar Enable bootvar debugging
callhome Enable debugging for Callhome
fc2 Configure FC2 debugging
fcc Enable FCC debugging
fcdomain Enable fcdomain debugging
fcfwd Enable fcfwd debugging
fcns Debug name server
fcs Configure Fabric Configuration Server Debugging
flogi Configure flogi debug
fspf Configure FSPF debugging
hardware Debug hardware, kernel loadable module parameters
ipconf Enable IP configuration debugging
ipfc Enable IPFC debugging
klm Debug kernel loadable module parameters
logfile Direct debug output to logfile
mcast Enable mcast debugging
mip Debug multiple IP kernel driver
module Configure LC Manager debugging
ntp Debug NTP module
platform Configure Platform Manager debugging
port Configure port debugging
port-channel Enable port-channel debug

Cisco MDS 9000 Series Specifications

General

Category	Switch
Operating System	Cisco NX-OS
Ports	Varies by model
Protocols	Fibre Channel (FC), Fibre Channel over IP (FCIP), iSCSI
Redundancy	Redundant supervisors, power supplies, and fans
Management	Cisco Data Center Network Manager (DCNM), CLI, SNMP
Virtualization Support	VSANs (Virtual SANs)
Security Features	Fibre Channel Security Protocol (FC-SP)
Hot Swappable Components	power supplies, fans
Power Supply Options	AC and DC options available