Cisco MDS 9000 Series

Send comments to mdsfeedback-doc@cisco.com.
3-12
Cisco MDS 9000 Family Troubleshooting Guide
OL-5183-02, Cisco MDS SAN-OS Release 1.3
Chapter 3 Troubleshooting Switch Level Issues and Interswitch Connectivity
Troubleshooting TE Port Connectivity - VSAN Isolation
beacon(off), snmp trap(on), tem(false)
rx bb_credit(default), rx bb_credit multiplier(default)
rxbufsize(2112), encap(default), user_cfg_flag(0x3)
description()
Operational Info - state(trunking), mode(TE), speed(2 Gbps), trunk(on)
state reason(None)
phy port enable (1), phy layer (FC)
participating(1), port_vsan(7), fcid(0x000000)
rx bb_credit multiplier(0), rx bb_credit(12)
current state [PI_FSM_ST_TEPORT_INIT_TRUNKING_ENABLED]
port_init_eval_flag(0x00000001), cfg wait for none
Mts node id 0x202
eport_init_flag(0x00000386), elp_chk_flag(0x0000000A)
elp_rcvd_fc2_handle(0x00000000), elp_sent_fc2_handle(0x0800864E)
esc_chk_flag(0x0000002A), esc_fc2_handle(0x0801864F)
elp_flags(0x0000), classes_supported(F,2,3), tx bb_credit(255)
cnt_link_failure(1), cnt_link_success(5), cnt_port_up(0)
cnt_cfg_wait_timeout(0), cnt_port_cfg_failure(0), cnt_init_retry(0)
oper trunk mode(on)
Port Capabilities -
Modes: E,TE,F,FL,TL,SD
Min Speed: 1000
Max Speed: 2000
Max Sourcable Pkt Size: 2112
Max Tx Bytes: 2112
Max Rx Bytes: 2112
Max Tx Buffer Credit: 255
Max Rx Buffer Credit: 12
Max Rx Buffer Credit (ISL): 12
Default Rx Buffer Credit: 12
Default Rx Buffer Credit(ISL): 12
Default Rx Buffer Credit Multiplier: 0
Rx Buffer Credit change not allowed
Max Private Devices: 63
Hw Capabilities: 0xb
Connector Type: 0x0
FCOT info -
Min Speed: 1000
Max Speed: 2000
Module Type: 8
Connector Type: 7
Gigabit Eth Compliance Codes: 0
FC Transmitter Type: 3
Vendor Name: IBM
Vendor ID: 8:0:90
Vendor Part Num: IBM42P21SNY
Vendor Revision Level: AA20
Trunk Info -
trunk vsans (allowed active) (1,7-8)
trunk vsans (up) (7)
trunk vsans (isolated) (1,8)
TE port per vsan information
fc2/29, Vsan 1 - state(down), state reason(Isolation due to domain other side eport
isolated), fcid(0x000000)
port init flag(0x10000), current state [TE_FSM_ST_ISOLATED_DM_ZS]
fc2/29, Vsan 7 - state(up), state reason(None), fcid(0x690202)
port init flag(0x38000), current state [TE_FSM_ST_E_PORT_UP]
fc2/29, Vsan 8 - state(down), state reason(Isolation due to vsan not configure
d on peer), fcid(0x000000)
port init flag(0x0), current state [TE_FSM_ST_ISOLATED_VSAN_MISMATCH]
switch#