Cisco MDS 9000 Series

Send comments to mdsfeedback-doc@cisco.com.
4-18
Cisco MDS 9000 Family Troubleshooting Guide
OL-5183-02, Cisco MDS SAN-OS Release 1.3
Chapter 4 Troubleshooting Switch Fabric Level Issues
Troubleshooting Zoning Issues
The system output looks like this:
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface fc1/14 is down
(Channel admin down)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface fc1/15 is down
(Channel admin down)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface fc1/16 is down
(Channel admin down)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_DOWN: Interface
port-channel 1 is down (No operational members)
Nov 19 10:26:10 switch4 %LOG_PORT-5-IF_DOWN_ADMIN_DOWN: Interface port-channel 1 is down
(Administratively down)
Nov 19 10:26:10 switch4 %LOG_PORT_CHANNEL-5-FOP_CHANGED: port-channel 1: first operational
port changed from fc1/16 to none
Step 4 To reactivate the connection to the zone to be merged, enter the following command:
switch4(config-if)#
switch4(config-if)# no shut
The system output looks like this:
switch4(config-if)# Nov 19 10:28:11 switch4 %LOG_PORT_CHANNEL-5-FOP_CHAN
GED: port-channel 1: first operational port changed from none to fc1/15
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_UP: Interface port-channel 1 is up in mode TE
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/14, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/15, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/16, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/14, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/15, vsan 1 is up
Nov 19 10:28:21 switch4 %LOG_PORT-5-IF_TRUNK_UP: Interface fc1/16, vsan 1 is up
Step 5 To exit config mode and check the active zone sets, enter the following command:
switch4(config-if)# exit
switch4(config)# exit
switch4# show zoneset active
The system output looks like this:
zoneset name wall vsan 1
zone name excal1 vsan 1
* fcid 0x620200
fcid 0x6200ca
zone name $default_zone$ vsan 1
* fcid 0x6e00da
* fcid 0x6e00d9
* fcid 0x6e00d6
* fcid 0x6e0100
* fcid 0x6201ca
* fcid 0x6201cb
* fcid 0x6201cc
* fcid 0x6201cd
* fcid 0x6201ce
* fcid 0x6201d1
* fcid 0x6201d2
* fcid 0x6201d3
* fcid 0x6201d4
* fcid 0x6201d5
switch4#