EasyManuals Logo

Cisco MDS 9000 Series Troubleshooting Guide

Cisco MDS 9000 Series
161 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #97 background imageLoading...
Page #97 background image
Send comments to mdsfeedback-doc@cisco.com.
5-3
Cisco MDS 9000 Family Troubleshooting Guide
OL-5183-02, Cisco MDS SAN-OS Release 1.3
Chapter 5 Troubleshooting IP Storage Issues
Troubleshooting IP Connections
A sample output of the sh ips arp command follows.
switch# sh ips arp int giga 4/7
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.18.185.97 0 00:d0:01:3b:38:0a ARPA GigabitEthernet4/7
Internet 172.18.189.129 0 00:d0:01:3b:38:0a ARPA GigabitEthernet4/7
Internet 172.18.189.153 0 00:08:02:24:e0:8b ARPA GigabitEthernet4/7
Internet 172.18.189.155 0 00:08:02:df:93:77 ARPA GigabitEthernet4/7
Internet 172.18.189.156 9 00:08:02:b3:45:1b ARPA GigabitEthernet4/7
A sample output of the clear ips arp command follows. You clear the arp cache to verify that the activity
you are viewing is the most current.
switch# clear ips arp int gig4/7
arp clear successful
A sample output of the sh ips arp command follows.
switch# sh ips arp int giga 4/7
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.18.185.97 0 00:d0:01:3b:38:0a ARPA GigabitEthernet4/7
Internet 172.18.189.156 0 00:08:02:b3:45:1b ARPA GigabitEthernet4/7
A sample output of the sh ips arp command follows.
switch# sh ips arp int giga 4/7
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.18.185.97 0 00:d0:01:3b:38:0a ARPA GigabitEthernet4/7
Internet 172.18.189.129 0 00:d0:01:3b:38:0a ARPA GigabitEthernet4/7
Internet 172.18.189.156 0 00:08:02:b3:45:1b ARPA GigabitEthernet4/7
A sample output of the sh arp command follows.
switch# sh arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.18.185.97 0 00d0.013b.380a ARPA mgmt0
Step 3 Use the show interface command to verify that the Gigabit Ethernet interface is up. A sample output of
the show interface command follows.
GigabitEthernet4/7 is up
Hardware is GigabitEthernet, address is 0005.3000.9f58
Internet address is 172.18.189.137/26
MTU 1500 bytes, BW 1000000 Kbit
Port mode is IPS
Speed is 1 Gbps
Beacon is turned off
5 minutes input rate 688 bits/sec, 86 bytes/sec, 0 frames/sec
5 minutes output rate 312 bits/sec, 39 bytes/sec, 0 frames/sec
156643 packets input, 16859832 bytes
0 multicast frames, 0 compressed

Table of Contents

Other manuals for Cisco MDS 9000 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco MDS 9000 Series and is the answer not in the manual?

Cisco MDS 9000 Series Specifications

General IconGeneral
CategorySwitch
Operating SystemCisco NX-OS
PortsVaries by model
ProtocolsFibre Channel (FC), Fibre Channel over IP (FCIP), iSCSI
RedundancyRedundant supervisors, power supplies, and fans
ManagementCisco Data Center Network Manager (DCNM), CLI, SNMP
Virtualization SupportVSANs (Virtual SANs)
Security FeaturesFibre Channel Security Protocol (FC-SP)
Hot Swappable Componentspower supplies, fans
Power Supply OptionsAC and DC options available

Related product manuals