Thermostat control
Table 27: Thermostat control
Readout of the actual control state of the controller
0=Normal ctrl., 1=Hold after defrost, 4=Drip o,
10=Main switch OFF, 11=Thermostat cutout, 12=Frost
protection S4, 13=Not_used, 14=Defrost, 15=Fan de-
lay, 16=Forced closing, 17=Door open, 18=Melt peri-
od, 19=Modulating temp. control, 20=Emergency
control, 23=Adaptive superheat control, 24=Start in-
jection, 25=Manual control, 26=No refrigerant selec-
ted, 29=Case cleaning, 30=Forced cooling, 31=Door
open, 32=Power-up delay, 33=Air heating, 45=Shut
down controller, 48=Adaptive liquid control
Readout of the actual control state of the controller
0=Normal ctrl., 1=Hold after defrost, 4=Drip o,
10=Main switch OFF, 11=Thermostat cutout, 12=Frost
protection S4, 13=Not_used, 14=Defrost, 15=Fan de-
lay, 16=Forced closing, 17=Door open, 18=Melt peri-
od, 19=Modulating temp. control, 20=Emergency
control, 23=Adaptive superheat control, 24=Start in-
jection, 25=Manual control, 26=No refrigerant selec-
ted, 29=Case cleaning, 30=Forced cooling, 31=Door
open, 32=Power-up delay, 33=Air heating, 45=Shut
down controller, 48=Adaptive liquid control
Readout of the actual control state of the controller
0=Normal ctrl., 1=Hold after defrost, 4=Drip o,
10=Main switch OFF, 11=Thermostat cutout, 12=Frost
protection S4, 13=Not_used, 14=Defrost, 15=Fan de-
lay, 16=Forced closing, 17=Door open, 18=Melt peri-
od, 19=Modulating temp. control, 20=Emergency
control, 23=Adaptive superheat control, 24=Start in-
jection, 25=Manual control, 26=No refrigerant selec-
ted, 29=Case cleaning, 30=Forced cooling, 31=Door
open, 32=Power-up delay, 33=Air heating, 45=Shut
down controller, 48=Adaptive liquid control
Readout of food temperature
Status of the day/night operation (night operation:
on/o)
Readout of the actual cut-in value for the thermostat
Readout of the actual cut-out value for the thermo-
stat
Read the ongoing cut-in time for the thermostat or
the duration of the last completed cut-in
Read the ongoing cut-in time for the thermostat or
the duration of the last completed cut-in
Read the ongoing cut-in time for the thermostat or
the duration of the last completed cut-in
Readout of which thermostat is used for regulation:
1= Thermostat band 1
2= Thermostat band 2
Actual status of output function
Here it is dened how the thermostat is to be operat-
ed. Either as an ordinary ON/OFF thermostat or as a
modulating thermostat.When operation is ”modulat-
ing” the valve will limit the ow of refrigerant so that
the temperature variation will be less than for the
ON/OFF thermostat.The thermostat dierential (r01)
must not be set lower than 2K for ”modulating”. In a
decentralised plant you must select the ON/OFF ther-
mostat setting.
1=ON/OFF, 2=Modulating, 3=ON/OFF Common
Select which sensor to be used for the thermostat
control
1=Ther. air A, 2=Average all, 3=Maximum all
Setpoint. The thermostat’s cut-out value when the
given thermostat band is in use
© Danfoss | Climate Solutions | 2022.08 BC365022028193en-000201 | 43
AK-CC55 Multi Coil