Danfoss AK-CC55 Multi Coil User Manual

Fan control
Table 35: Fan control
Function
Description
Values
Code
Short name
Control state A
Readout of the actual control state of the controller
0=Normal ctrl., 1=Hold after defrost, 4=Drip o,
10=Main switch OFF, 11=Thermostat cutout, 12=Frost
protection S4, 13=Not_used, 14=Defrost, 15=Fan de-
lay, 16=Forced closing, 17=Door open, 18=Melt peri-
od, 19=Modulating temp. control, 20=Emergency
control, 23=Adaptive superheat control, 24=Start in-
jection, 25=Manual control, 26=No refrigerant selec-
ted, 29=Case cleaning, 30=Forced cooling, 31=Door
open, 32=Power-up delay, 33=Air heating, 45=Shut
down controller, 48=Adaptive liquid control
u00
u00 Ctrl. state
Control state B
Readout of the actual control state of the controller
0=Normal ctrl., 1=Hold after defrost, 4=Drip o,
10=Main switch OFF, 11=Thermostat cutout, 12=Frost
protection S4, 13=Not_used, 14=Defrost, 15=Fan de-
lay, 16=Forced closing, 17=Door open, 18=Melt peri-
od, 19=Modulating temp. control, 20=Emergency
control, 23=Adaptive superheat control, 24=Start in-
jection, 25=Manual control, 26=No refrigerant selec-
ted, 29=Case cleaning, 30=Forced cooling, 31=Door
open, 32=Power-up delay, 33=Air heating, 45=Shut
down controller, 48=Adaptive liquid control
U74
U74 Ctrl.State B
Control state C
Readout of the actual control state of the controller
0=Normal ctrl., 1=Hold after defrost, 4=Drip o,
10=Main switch OFF, 11=Thermostat cutout, 12=Frost
protection S4, 13=Not_used, 14=Defrost, 15=Fan de-
lay, 16=Forced closing, 17=Door open, 18=Melt peri-
od, 19=Modulating temp. control, 20=Emergency
control, 23=Adaptive superheat control, 24=Start in-
jection, 25=Manual control, 26=No refrigerant selec-
ted, 29=Case cleaning, 30=Forced cooling, 31=Door
open, 32=Power-up delay, 33=Air heating, 45=Shut
down controller, 48=Adaptive liquid control
U83
U83 Ctrl.State C
Fan
Actual status of output function
0=OFF, 1=ON
u59
u59 Fan relay
Fan pulsing mode
Pulse operation of fan
0: No pulse operation
1: Pulse operation when the thermostat is cut out
2: Pulse operation when the thermostat is cut out, but
only during night operation
0=No pulsing, 1=Pulsing cut-out, 2=Pulsing cut-out
night
F05
F05 FanPulseMode
Fan period time
Period time for pulsing of fan
F06
F06 Fan cycle
Fan ON cycle
ON time for fan. The ON period is set as a percentage
of the period time
F07
F07 Fan ON %
Fan stop high S5
temp.
Fan stop temperature The function stops the fans in
an error situation, so that they will not provide power
to the appliance. If the defrost sensor registers a high-
er temperature than the one set here, the fans will be
stopped. There will be re-start at 2 K below the set-
ting. The function is not active during a defrost or
start-up after a defrost.
F04
F04 FanStop temp
Fan at forced closing
You can set whether fans should be operational or
stopped if the function "Forced closing" is activated
here.
0: Fans are OFF
1: Fans are ON
2: Fans are OFF and defrost is not permitted
3: Fans are ON and defrost is not permitted
0=OFF, 1=ON, 2=OFF and suppress defrost, 3=ON and
suppress defrost
o90
o90 Fan ForcedCl
Fan stop at blinds
closing
When blinds are closing the fans are stopped in the
dened time delay in order to ensure that the blinds
are closed correctly
P65
P65 BlindFanStop
© Danfoss | Climate Solutions | 2022.08 BC365022028193en-000201 | 51
AK-CC55 Multi Coil

Danfoss AK-CC55 Multi Coil Specifications

General

Brand	Danfoss
Model	AK-CC55 Multi Coil
Category	Controller
Language	English