Danfoss VLT AQUA Drive FC 202

10 Specications
10.1 Electrical Data
10.1.1 Electrical Data, 380–480 V AC
Table 99: Electrical Data, Mains Supply 3x380–480 V AC
FC 202
N110
N132
N160
High/normal overload
High overload=150% or 160% torque for a duration of 60 s. Normal
overload=110% torque for a duration of 60 s.
HO
NO
HO
NO
HO
NO
Typical shaft output at 400 V [kW]
90
110
110
132
132
160
Typical shaft output at 460 V [hp]
125
150
150
200
200
250
Typical shaft output at 480 V [kW]
110
132
132
160
160
200
Enclosure size
D9h
D9h
D9h
Output current (3-phase)
Continuous (at 400 V) [A]
177
212
212
260
260
315
Intermittent (60 s overload) (at 400 V) [A]
266
233
318
286
390
347
Continuous (at 460/480 V) [A]
160
190
190
240
240
302
Intermittent (60 s overload) (at 460/480 V) [A]
240
209
285
264
264
332
Continuous kVA (at 400 V) [kVA]
123
147
147
180
180
218
Continuous kVA (at 460 V) [kVA]
127
151
151
191
191
241
Continuous kVA (at 480 V) [kVA]
139
165
165
208
208
262
Maximum input current
Continuous (at 400 V) [A]
171
204
204
251
251
304
Continuous (at 460/480 V) [A]
154
183
183
231
231
291
Maximum number and size of cables per phase
- Mains [mm
2
(AWG)]
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
- Mains with disconnect [mm
2
(AWG)]
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
- Mains with fusible disconnect [mm
2
(AWG)]
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
- Mains with contactor [mm
2
(AWG)]
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
- Motor [mm
2
(AWG)]
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
2x95 (2x3/0 mcm)
Drive module power loss at 400 V [W]
(1)(2)(3)
2031
2559
2289
2954
2923
3770
Drive module power loss at 460 V [W]
(1)(2)(3)
1828
2261
2051
2724
2089
3628
Drive eciency
(2)
0.98
0.98
0.98
Output frequency [Hz]
(4)
0–590
0–590
0–590
Heat sink overtemperature trip [°C (°F)]
110 (230)
110 (230)
110 (230)
AQ262141056213en-000201 / 130R0882142 | Danfoss A/S © 2020.09
Specications
VLT® AQUA Drive FC 202
Operating Guide