Datalogic QuickScan QD2590 User Manual

SETUP
16 QUICKSCAN™ QD2590
Configuring Other Features
If your installation requires different programming than the standard factory default
settings, the following sections of this manual allow configuration of non-interface-spe-
cific settings you might require:
Configuration Using Bar Codes: General Features includes programming for scanning,
beeper and LED indicators and other such universal settings.
Reading Parameters: Reading Parameters include programming for scanning, beeper
and LED indicators and other universal settings.
1D Symbologies: Includes options concerning the bar code label types (symbologies).
These settings allow you to enable/disable symbologies, set label lengths, require check
digit, etc.
Software Version Transmission
The software version of the device can be transmitted over the RS-232, Keyboard and
USB interfaces by scanning the following label.
Transmit Software Version
Resetting the Product Configuration to Defaults
Restore Custom Default Configuration
If you aren't sure what programming options are in your reader, or you've changed
some options and want to restore the Custom Default Configuration that may have
been saved in the reader, scan the Restore Custom Default Configuration bar code
below. This will restore the custom configuration for the currently active interface.
Restore Custom Default Configuration
NOTE: Custom defaults are based on the interface type. Configure the
reader for the correct interface before scanning this label.

Datalogic QuickScan QD2590 Specifications

General

Type	Handheld bar code reader
Sensor type	-
Scanner type	1D/2D
Scanner resolution	0.17 mm
Tilt reading angle	0 - 360 °
Pitch reading angle	0 - 65 °
Light levels (direct sunlight)	0 - 100000 lx
Linear (1D) barcodes supported	CPC Binary, Codabar, Codabar 125, Code 11, Code 128, Code 128A, Code 128B, Code 128C, Code 25 (IR 2 of 5), Code 25 (non-IR 2 of 5), Code 3 of 9, Code 32, Code 39, Code 93, DUN 14, DataBar14, Discrete 2 of 5, EAN 128, EAN 2, EAN 5, EAN-13, EAN-8, Facing Identification Mark, GS1 DataBar, GS1 DataBar Expanded, GS1 DataBar Omnidirectional, GS1 Databar Limited, GS1-128 (UCC/EAN-128), HIBC, IATA, ISBN, ISSN, ITF-14, ITF-6, Industrial 2 of 5, Intelligent Mail, Interleaved 2 of 5, JAN, Latent image, MSI, Matrix 2 of 5, PDF417, PLANET, POSTNET, Pharmacode, Plessey, PostBar, RM4SCC / KIX, S-Code, Telepen, Trioptic, U.P.C., UPC-A, UPC-E
Optical sensor resolution (W x H)	1280 x 800 pixels
2D (matrix & stacked) barcodes supported	Aztec Code, Data Matrix, Dot Code A, MaxiCode, Micro QR Code, QR Code
Cable length	2 m
Standard interfaces	USB
Connectivity technology	Wired
Product color	Black
Image formats supported	BMP, JPEG, TIFF
International Protection (IP) code	IP52
Input voltage	5 V
Power consumption	450 mA
Cables included	USB Type-C
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	0 - 95 %
Sustainability certificates	RoHS
Material	Polyvinyl chloride (PVC)
Connector 1	USB C
Product type	USB cable
Connector gender	Male/Male
Brand compatibility	Datalogic
Connector 1 form factor	Straight
Harmonized System (HS) code	84733020

Weight and Dimensions

Depth	126 mm
Width	148 mm
Height	68 mm
Weight	145 g