Denon AVR-1508 User Manual


Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting
ENGLISH
Setup
k ~ A5 Distance
Set distance from listening position to speakers.
Before making the settings, measure the distance from the
listening position to the different speakers.
[Display]
1 . S p 2 . I n 3 . O p
Q
S p e a k e r S e t u p
Q
8 F L 1 2 f t
Q
1 5 S W 1 2 f t
Distance measurement
Select the speaker you want to set, then set the distance.
Set the value closest to the measured distance.
[Variable range]
0ft ~ 60ft
: Settable in units of 1 foot.
NOTE
Set the distance between the listening position and the various
speakers to no more than 20 ft.
A6 Crossover Frequency
Select crossover frequency from which subwoofer handles low
range signal.
[Display]
1 . S p 2 . I n 3 . O p
Q
S p e a k e r S e t u p
Q
1 6 C r . O v e r 8 0 H z
[Selectable items]
40Hz 60Hz 80Hz 90Hz 100Hz 110Hz 120Hz 150Hz
200Hz 250Hz
:
Only the portion of the bass sound of the various speakers output
from the subwoofer that has a frequency below the frequency set
here is output.
Set this according to the low frequency reproduction capabilities of the
speakers you are using.
• The “Crossover Frequency” can be set when there are speakers that
have been set to “Small” at “System Setup” – “Speaker Setup” or
when “Subwoofer” is set to “Yes” (vpage 20).
• For speakers set to “Small”, sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• Always set the crossover frequency to “80Hz”. When using small
speakers, however, we recommend setting the crossover frequency
to a higher frequency.
A7 Test Tone
Adjust channel levels to obtain equal volume from all speakers.
[Display]
1 . S p 2 . I n 3 . O p
Q
S p e a k e r S e t u p
Q
1 7 T . T o n e Y e s <
Q
T . T o n e A u t o >
Q
T e s t T o n e O n
Q
A u t o - F L
Test Tone
Select test tone playback method.
[Selectable items]
Auto
: Automatically switch speaker from which test tone is
output.
Manual
: Manually switch speaker from which test tone is output.
Test Tone Start
Press the o button to select “Yes”, then press the o p button to select
“Auto” or “Manual”.
Then press the i button. Out put the test tone.
Auto : Press the o p button to adjust the volume.
Manual : Press the u i button to select the speaker, then press the
o p button to adjust the volume.
When the adjustments are completed, press the ENTER button to
finish the test tone.
[Variable range]
–12dB
~
0dB
~
+12dB
Operations (vpage 19)

Denon AVR-1508 Specifications

General

HDMI Inputs	2
HDMI Outputs	1
Dolby Digital	Yes
DTS	Yes
AM/FM Tuner	Yes
Response Bandwidth	10 Hz - 100 kHz
Signal-To-Noise Ratio	98 dB
THD	0.08%
Input Impedance	47 kOhm
Input Sensitivity	200 mV
Tuner Type	Digital
Preset Station Qty	56
HDMI Switching	Yes
Tuning Range	FM: 87.5 - 108 MHz, AM: 522 - 1620 kHz
Audio D/A Converter	24-bit / 192 kHz
Output Impedance / Channel	8 Ohm
Frequency Response	10 Hz - 100 kHz
Channels	7.1
Power Output	75W per channel (8 ohms, 20Hz-20kHz, 0.08% THD)
Output Power / Channel	75W (8 ohms)