EasyManuals Logo

Denon AVR-1508 User Manual

Denon AVR-1508
62 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #38 background imageLoading...
Page #38 background image

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
ENGLISH

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
iPod
®
Playback
The music on an iPod can be played by using the Control Dock for
iPod (ASD-1R, sold separately).
The operation can also be performed using the buttons on the
remote control unit.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
b The iPod may only be used to copy or play contents that are not
copyrighted or contents for which copying or playback is legally
permitted for your private use as an individual. Be sure to comply
with applicable copyright legislation.
1
Make the necessary preparations.
q Set the iPod in the DENON Control Dock for iPod.
(vSee the Control Dock for iPod’s operating instructions.)
w Assign the Control Dock for iPod’s input.
”System Setup” ”Input Setup” ”iPod Assign”
(vpage 23)
2
Either turn <SOURCE SELECT> or press [iPod] to
select the input source assigned in step 1-w above.
R e m o t e i P o d
b If the displays above are not displayed, the iPod may not be
properly connected. Try connecting again.
3
Set [MODE SELECTOR 1] to “AUDIO” and [MODE
SELECTOR 2] to “iPod/NETWORK”.
(vpage 39 “Remote Control Unit Operations”)
Basic Operation
With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
Use the RESTORER mode to expand the low and high frequency
components of compressed audio les and achieve a richer sound.
The default setting is “Mode3” (vpage 29).
Press <ON/STANDBY> and set the AVR-1508’s power to the standby
mode before disconnecting the iPod. Also switch the input source to
one to which “iPod Assign” is not assigned before disconnecting the
iPod.
<SOURCE SELECT> STATUS
op
ui
<ON/STANDBY>
uiop
[1]
[6], [7]
[8], [9]
[2]
[CHANNEL +]
[CHANNEL –]
[ENTER]
STATUS
[MODE
SELECTOR 1]
[MODE
SELECTOR 2]
[Front]
About the button names in these explanations
< > : Buttons on the main unit
[ ] : Buttons on the remote control unit
Button name only:
Buttons on the main unit and remote control unit
uiop
[ENTER]
[iPod]
[MODE]
[Rear]
Searching Categories
1
Press o p.
C A T : R o c k
2
Use o p to select the category, then use ui to select
the desired station.
Channel category
“LOADING” is displayed while stations or data are being received.
“UPDATING” is displayed while the encording code is being
updated.
“XM – – –” is displayed if the selected channel cannot be used.
NOTE
Depending on the type of iPod and the software version, some
functions may not operate.
DENON will accept no responsibility whatsoever for any loss of iPod
data.

Table of Contents

Other manuals for Denon AVR-1508

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-1508 and is the answer not in the manual?

Denon AVR-1508 Specifications

General IconGeneral
HDMI Inputs2
HDMI Outputs1
Dolby DigitalYes
DTSYes
AM/FM TunerYes
Response Bandwidth10 Hz - 100 kHz
Signal-To-Noise Ratio98 dB
THD0.08%
Input Impedance47 kOhm
Input Sensitivity200 mV
Tuner TypeDigital
Preset Station Qty56
HDMI SwitchingYes
Tuning RangeFM: 87.5 - 108 MHz, AM: 522 - 1620 kHz
Audio D/A Converter24-bit / 192 kHz
Output Impedance / Channel8 Ohm
Frequency Response10 Hz - 100 kHz
Channels7.1
Power Output75W per channel (8 ohms, 20Hz-20kHz, 0.08% THD)
Output Power / Channel75W (8 ohms)

Related product manuals