Denon AVR-1509 Owner's Manual

For details on how to select, set and cancel settings for each menu, see “System Setup Operation” (vpage 18).
A0 Auto Preset Memory
Use the auto preset function to program radio stations.
If an FM station cannot be preset automatically, select the desired
station by tuning it in manually, then preset it manually.
Press o to start.
• “CH” blinks on the display and searching begins.
• “Completed” appears once searching is completed.
[Display]
1 . S p 2 . I n 3 . O p
W
I n p u t S e t u p
W
1 0 P r e s e t < S t a r t
NOTE
“Auto Preset Memory” is displayed when the input source is “FM”
and “AM”.
a ~ d Volume Control
Set the main zone volume setting.
a Volume Limit
Make a setting for maximum volume.
[Selectable items]
OFF
: Do not set a maximum volume.
–20dB
: Set the maximum volume to –20 dB.
–10dB
: Set the maximum volume to –10 dB.
0dB
: Set the maximum volume to 0 dB.
s Power On Level
This sets the volume set when the main zone’s power is turned on.
[Selectable items]
Last
: Use the memorized setting from the last session.
– – –
: Always use the muting on condition when power
is turned on.
[Variable range]
–80dB ~ +18dB
: Set the volume level when the power is turned on
in units of 1 dB.
b
The variable level when upper limit has been set with “Volume
Limit” is “–80 dB ~ the set volume level”.
3. Option Setup
Make various other settings.
a ~ d Volume Control
f Auto Surround Mode
g Direct Mode Setup
h Remote ID Setup
[Display]
1 . S p 2 . I n 3 . O p
E
O p t i o n S e t u p
E
1 L i m i t : O F F
E
2 P . O n : L a s t
E
3 M u t e : F u l l
d Mute Level
This sets the amount of attenuation of the volume when the mute
mode is set in the main zone.
[Selectable items]
Full
: The sound is cut off entirely.
–40dB
: The sound is attenuated by 40 dB.
–20dB
: The sound is attenuated by 20 dB.
f Auto Surround Mode
Make setting for memorizing surround mode setting for each
input signal type.
[Selectable items]
ON
: Memorize settings. Most recently stored surround mode is
automatically selected.
OFF
: Do not memorize settings. Surround mode does not change
according to input signal.
The auto surround mode function lets you store in the memory the
surround mode last used for playing the three types of input signals
listed below.
q Analog and PCM 2-channel signals (STEREO)
w 2-channel signals of Dolby Digital, DTS or other multi-channel
format (DOLBY PLg Cinema)
e Multi-channel signals of Dolby Digital, DTS or other multi-channel
format (DOLBY/DTS SURROUND)
b Default settings are indicated in ( ).
[Display]
1 . S p 2 . I n 3 . O p
E
O p t i o n S e t u p
E
4 A u t o S u r r . : O N
[Selectable items]
ON
: Use MultEQ.
OFF
: Do not use MultEQ.
g Direct Mode Setup
Select MultEQ use for DIRECT mode playback.
[Display]
1 . S p 2 . I n 3 . O p
E
O p t i o n S e t u p
E
5 D i r e c t : O F F

Getting Started Connections Setup Playback Remote Control Information Troubleshooting
ENGLISH
Specifications

Denon AVR-1509 Specifications

General

Power Output	75 W per channel (8 ohms, 20Hz-20kHz, 0.08% THD)
Number of Channels	5.1
HDMI Inputs	2
HDMI Outputs	1
Response Bandwidth	10Hz-100kHz
Signal-To-Noise Ratio	98 dB
Total Harmonic Distortion	0.08%
Input Impedance	47 kOhm
Input Sensitivity	200 mV
Tuner Type	Digital
Tuner Bands	AM/FM
Preset Station Qty	56
HDMI Switching	Yes
Output Impedance / Channel	8 ohms
Frequency Response	10Hz-100kHz
Digital Audio Inputs	2 Optical, 1 Coaxial
Dolby Formats	Dolby Digital, Dolby Pro Logic II
DTS Formats	DTS, DTS Neo:6
Surround Sound Effects	Virtual Surround
Audio D/A Converter	192kHz/24-bit
Output Power / Channel	75 W
Tuner Frequency Range	FM: 87.5-108 MHz, AM: 522-1611 kHz
Video Inputs/Outputs	Component video input (2), Component video output (1), Composite video input (4), Composite video output (2)
Analog Audio Inputs/Outputs	4 Analog Audio Inputs, 1 Analog Audio Output