A4 Tone Control
Turn tone adjustments on and off.
[Selectable items]
ON
: Allow tone adjustment (treble, bass).
OFF
: Playback without tone adjustment.
The tone cannot be adjusted when in the DIRECT mode.
A5 Bass
Adjust low frequency range (bass).
[Variable range]
–6dB
~
0dB
~
+6dB
A6 Treble
Adjust high frequency range (treble).
[Variable range]
–6dB
~
0dB
~
+6dB
“Bass” and “Treble” can be set when “Tone Control” is set to “ON”.
A2 SW ATT (Subwoofer Attenuation)
Attenuate subwoofer level when using EXT. IN mode.
[Selectable items]
ON
: The input from the subwoofer channel is attenuated.
OFF
: The input from the subwoofer channel is not attenuated.
Usually use in this mode.
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
A3 Subwoofer
Turn subwoofer output on and off.
[Selectable items]
ON
: The subwoofer is used.
OFF
: The subwoofer is not used.
For details on adjusting individual parameters, see “Adjusting the Parameters” (vpage 25).
• If the settings of speakers for which “None” has been determined
at “Auto Setup” are changed, “Audyssey”, “Audyssey Byp. L/R”
and “Audyssey Flat” cannot be selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with “System
Setup” – “Speaker Setup” – “Restore”.
• When using headphones, “MultEQ” is set to “OFF”.
A7 MultEQ
Select the type of correction desired from the following list:
[Selectable items]
Audyssey
: Optimize frequency response of all speakers.
Byp. L/R
: Optimize frequency response of speakers except front
L and R speakers.
Flat
: Optimize frequency response of all speakers to flat
response.
OFF
: Turn equalizer off.
NOTE
• “MultEQ” can only be set when Auto Setup has been performed.
• “MultEQ” cannot be set in the following situations.
•
If “Auto Setup” fails to be completed.
•
After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
Operating from the main unit or remote
control unit
Press MULTEQ.
• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
selected, the Audyssey MultEQ indicator lights green.
• After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level and Crossover Frequency have changed without
increasing the number of speakers measured, the Audyssey MultEQ
indicator lights red.
NOTE
When the “Dynamic EQ” setting is “ON”, setting is not possible.
A8 Dynamic EQ
Audyssey Dynamic EQ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ to provide well-balanced sound for every listener
at any volume level.
NOTE
• “Dynamic EQ” can only be set when auto setup has been
performed.
• “Dynamic EQ” cannot be set in the following situations.
• If “Auto Setup” fails to be completed.
• After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• When “MultEQ” is set to “OFF”, “Dynamic EQ” is automatically set
to “OFF”.
• “Night Mode” and “Tone Control” cannot be used jointly.
[Selectable items]
ON
: Use Dynamic EQ function.
OFF
: Do not use Dynamic EQ function.
Operating from the main unit or remote
control unit
Press DYNAMIC VOLUME.
Before running Auto Setup and after running Auto Setup, if the number
of speakers has increased or you pressed DYNAMIC VOLUME, “Run
Audyssey” is displayed. In this case, either perform Auto Setup again,
or return to the setting after running Auto Setup with “System Setup”
– “Speaker Setup” – “Restore”.
n Operating conditions for each function
• Dynamic EQ : When “MultEQ” is set to “ON”
• Dynamic Volume : When “Dynamic EQ” is set to “ON”
• DV setting : When “Dynamic Volume” is set to “ON”
A7 MultEQ
A8 Dynamic EQ
A9 Dynamic Volume
S0 DV Setting
Getting Started Connections Setup Playback Remote Control Information Troubleshooting
ENGLISH
Specifications
To Next Page
Loading...
Need help?
General
