Need help?Do you have a question about the DEWESOFT Krypton and is the answer not in the manual?
General| Series | Krypton |
|---|---|
| IP Rating | IP67 |
| Power Supply | 9 - 36 V DC |
| Resolution | 24-bit |
| Communication Interface | Ethernet |
| Input Type | Analog, Digital, Counter, CAN |
Guide to installing the Dewesoft software for optimal operation.
Basic instructions for connecting Krypton devices to a PC.
How to configure Krypton devices within Dewesoft settings.
Setting up channels for connected Krypton devices in Dewesoft.
Covers measurement basics and Krypton configuration.
Details on setting up analogue channels and amplifier settings.
Explains the importance and selection of sample rates for Krypton devices.
Navigating and using the Measure mode in Dewesoft for live data.
Using Dewesoft's Analyse mode to review and analyze recorded data.
Checking and configuring hardware setup through the Dewesoft settings dialogue.
Step-by-step guide for downloading and performing firmware upgrades.
Steps to resolve issues when Krypton devices are not found by Dewesoft.
Key features of the KRYPTON DAQ system, including distributed DAQ and EtherCAT.
Details on EtherCAT protocol, data transmission, and zero configuration.
Information on the robust construction, IP67 rating, and environmental resistance.
Overview of various KRYPTON modules for different signal types like STG, TH, RTD, etc.
How KRYPTON ensures microsecond accuracy synchronization across devices.
Detailed specifications for KRYPTON interface, power, environmental, and physical properties.
Provides a comparative overview of KRYPTON multichannel modules.
Details on KRYPTON multichannel modules, including connectors and data rates.
Dimensions and form factor of KRYPTON single width modules.
Dimensions and form factor of KRYPTON dual width modules.
Technical specifications for the KRYPTON ONE series of modules.
Detailed dimensions and physical characteristics of KRYPTON ONE modules.
Illustrates typical connection diagrams for measurement chains.
Detailed specifications for KRYPTON-4xACC and KRYPTON-8xACC modules.
Details on the KRYPTON-8xACC module and its BNC connectors.
Details on the KRYPTON-4xACC module and its BNC connectors.
Pin-out details for the BNC connector on ACC modules.
Wiring diagrams for ACC modules for Voltage and IEPE inputs.
Detailed specifications for the KRYPTON-1xAO module.
Pin-out details for the BNC connector on AO modules.
Specifications for the KRYPTONi-2xCAN-USB module.
Specifications for KRYPTONi-1xCAN and KRYPTONi-1xCAN-FD modules.
Pin-out details for CAN connectors (DSUB-9 male).
Detailed specifications for the KRYPTON-1xCNT module.
Pin-out details for the LEMO 7-pin female connector on CNT modules.
Specifications for KRYPTONi-16xDI, 8xDI-8xDO, and 16xDO modules.
Details on the KRYPTONi-16xDI module with 16 digital input channels.
Details on the KRYPTONi-16xDO module with 16 digital output channels.
Information on the KRYPTONi-8xDI-8xDO module with mixed digital I/O.
Pin-out diagrams for multichannel DIO modules.
Pin-out details for DSUB-15 HD connectors on 4xDI and 4xDO modules.
Detailed specifications for the high voltage input module.
Pin-out details for the HV connector (Banana plug).
Wiring diagram for HV module for Voltage input.
Detailed specifications for the KRYPTONi-8xLA module.
Pin-out details for the BNC connector on LA modules.
Wiring diagram for LA module for Current measurement.
Detailed specifications for KRYPTONi-4xLV and KRYPTONi-8xLV modules.
Pin-out details for the BNC connector on LV modules.
Wiring diagram for LV module for Voltage input.
Detailed specifications for the KRYPTONi-8xRTD module.
Pin-out details for the LEMO 0B 6-pin connector on RTD modules.
Wiring diagrams for RTD modules for Voltage and Resistance.
Wiring diagram for RTD modules for 3-wire temperature measurement.
Specifications for KRYPTON-3xSTG and KRYPTON-6xSTG modules.
Pin-out details for DSUB-9 female connectors on STG modules.
Wiring diagrams for STG modules for Voltage input (single-ended and differential).
Wiring diagrams for STG modules for Full, Half, and Quarter bridge configurations.
Specifications for KRYPTONi-8xTH and KRYPTONi-16xTH modules.
Pin-out details for thermocouple connectors.
Wiring diagrams for various thermocouple types (T, S, N, K).
Detailed specifications for the KRYPTON CPU, including computer, interfaces, and environmental data.
Overview of connectors available on the KRYPTON CPU.
Pin-out details for the 3-pin LEMO male power connector.
Introduction to the ECAT Power Junction box for power and data injection.
Pin-out details for the 8-pin LEMO female EtherCAT connector.
Information on the ECAT Power Injector box for long measurement chains.
Pin-out details for the 8-pin LEMO female PWR connector on the Power Injector.
Introduction to the ECAT Sync Junction for synchronizing EtherCAT lines.
Pin-out details for the 4-pin LEMO female Sync connector.
Introduction to the ECAT GPS Junction for GPS and IRIG-B synchronization.
Pin-out details for the 4-pin LEMO female Sync connector.
Details on the EtherCAT connector and cables used.
Pin-out details for the 8-pin LEMO male EtherCAT IN connector.
Pin-out details for the 8-pin LEMO female EtherCAT OUT connector.
Explanation of the LED indicators (L, D) and their blinking codes.
Description of the INIT state for Krypton slices and LED behavior.
Description of the SAFE-OP state for slow sampling rate data reading.
Description of the OP state for desired sampling rate data reading.
Instructions on how to stack and lock KRYPTON modules together.
Overview of aluminum mounting plates for KRYPTON modules.
Connection guide for systems using only EtherCAT devices.
Information on using the Power Injector box for long EtherCAT measurement chains.
How to use the Power Junction box to combine Ethernet and power lines.
Guide for setting up distributed systems using Krypton ONE devices.
Information on Sync and GPS Junction boxes for synchronization.
Solutions for using multiple EtherCAT chains with synchronized synchronization.
Using a multi-port Ethernet computer for synchronized EtherCAT chains.
Explanations of important terms and abbreviations.
General safety precautions to be observed during operation, service, and repair.
Information about the environmental impact and recycling of the product.
Records of previous versions and updates to the KRYPTON manual.
To Next Page
