The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
55
175
Load-value is Units? - Is the parameter programmed in Q.172 for event counter 4 the number of units?
No / Yes
176
Load-value is Distance (in metres)? - Is the parameter programmed in Q.172 for event counter 4 the distance in metres?
No / Yes
177
Load-value is Wai! ng-Time (in seconds)? - Is the parameter programmed in Q.172 for event counter 4 the waiting-time in seconds?
No / Yes
178
Load-value is Cost of Fare? - Is the parameter programmed in Q.172 for event counter 4 the cost of the fare?
No / Yes
179
Load-value is Cost of Extra-Charge? - Is the parameter programmed in Q.172 for event counter 4 the cost of the extra-charge?
No / Yes
180
Reload every Metre? (if not: every Second) - Event Counter 4 must be reloaded every metre? If not then it will be reloaded every
second. The allowed answer is either: 0 (No: every second) or: 1 (Yes: every metre).
No / Yes
181
Act. Only Above cross-speed? (if not: Allw.) - Event Counter 4 should be activated only above the cross-speed? If not then it will allways
be activated. The allowed answer is either: 0 (No: always) or: 1 (Yes: only above).
No / Yes
182
Event-Counter n.4 is moment. suspended? - Event Counter number 4 should be momentarily suspended? If not then it will be active.
The allowed answer is either: 0 (No: active) or: 1 (Yes: suspended).
No / Yes
183
At tariff -change discard accumul. Dist/Time? - If the tariff is changed manually with key F2 should the accumulated distance or time be
discarded?
If not, the accumulated distance or time will be proportionaly accounted for. The allowed answer is either: 0 (No: account for) or: 1
(Yes: discard).
No / Yes
184
At tariff -change synchronize with next unit? - If the tariff is changed manually with key F2 should the current unit be completed with the
current
parameters? If not, the tariff-change will be immediate. The allowed answer is either: 0 (No: immediate) or: 1 (Yes: synchronize).
No / Yes
185
Extra-Charge n. 4 is a discount? - Extra-Charge n. 4, as programmed in Q.27, should be interpreted not as an extra-charge but as a
discount? The discount can only be used as a percentage. Therefore the parameter of Q.31 should be programmed as Yes. The
allowed answer is either: 0 (No: extra-charge) or: 1 (Yes: discount).
No / Yes
186
In ForHire disable keys F2, F3, F4 and F5? - In ForHire the keys F2, F3, F4 and F5 should be disabled? In case of Yes the taxi-meter
works normaly including the F1-key but all functions that can be invoked with the keys F2, F3, F4 and/or F5 are inhibited.
The allowed answer is either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
187
Start-of-Fare ! me is used for Night/Holiday extras? - Should the time in which the fare starts be considered for the calculation of the
night and/or holiday extras? In case of Yes and if there is a change from night/holiday time to normal time (or vice versa) during the
trip then for as long as the trip lasts the fare cost will be calculated as if it is still night/holiday time. Starting from the next fare the
parameters for normal time will be used.
The allowed answer is either: 0 (No) or: 1 (Yes).
No / Yes
188
Show fare and extra-charge divided by 100? - Should the fare and the extra-charge be shown on their resp. displays divided by 100?
In this way the two least signifi cant digits (usually zero) are not shown. The allowed answer is either: 0 (No: show normal) or:
1 (Yes: show divided by 100).
No / Yes
189
Available for any possible so# ware extension
190
In case Night/Holiday extras are added on Flag drop, have to be added also on Min. trip amount?
No / Yes
191
On Euro conversion apply the Arround func! on?
No / Yes
VA RIOUS FUNCTIONS
192
Disable auto-shutoff if car-lights are ON? - In Stopped with auto-shut-off disabled the taxi-meter will allways remain ON. In case auto-
shut-off is enabled the taxi-meter will switch OFF automatically after the amount of time programmed in Q.284. The allowed answer is
either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
193
Enable the light-test? When this option is enabled then in case of an error the message ‘ERROR’ ‘LIGHT’ will appear on the display. The
light-test is done on the moment of passing from Stopped to Hired. The lights tested are: TAXI, light 1 to light 4. The allowed answer is
either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
194
Block the taxi-meter on light-error? - At the end of the current fare should the taxi-meter be blocked in case of a light-error?
The allowed answer is either: 0 (No: don’t block) or: 1 (Yes: block).
No / Yes
To Next Page
Loading...