The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
65
393
Baudrate for COM 2: what is the baudrate (transmission-speed) of COM 2? The baudrate is given in baud with an accuracy of 1 baud.
The allowed value goes from 0 (min) to 65535 (max).
0 - 65535
baud
394
Maximum packet length for COM 2: what is the maximum length of a data-packet of COM 2? The packet length is given in byte with an
accuracy of 1 byte. The allowed value goes from 1 (min) to 512 (max).
1 - 512
395
First cost threshold for authoriza! on: this is the fi rst amount above which authorization is requested for acceptance of the payment
of the fare with a credit-card. The cost is given in the local currency with an accuracy of 1. The allowed value goes from 0 (min) to
1000000 (max).
1 -
1000000
396
Second cost threshold for authoriza! on: this is the second amount above which authorization is requested for acceptance of the
payment of the fare with a credit-card. The cost is given in the local currency with an accuracy of 1. The allowed value goes from 0 (min)
to 1000000 (max).
0 -
1000000
397
Third cost threshold for authoriza! on: this is the third amount above which authorization is requested for acceptance of the payment
of the fare with a credit-card. The cost is given in the local currency with an accuracy of 1. The allowed value goes from 0 (min) to
1000000 (max).
0 -
1000000
398
Time-out for authoriza! on of payment: this is the waiting-time during which authorization is requested for acceptance of the payment of
the fare with a credit-card. If the authorization is not obtained within this time then the request is considered denied. The waiting-time is
given in seconds with an accuracy of 0.1 second. The allowed value goes from 0.0 (min) to 6553.5 (max). The digit indicating multiples
of 0.1 sec. (so at the right of the decimal point) will fl ash.
0 - 65535
seconds
399
Time-Out keyboard locked: this is the time after which the keyboard gets unlocked (activated) automatically if WD-commands are not
received anymore. As long as this time has not passed the keyboard remains locked (not active).
This is valid for a time-out value of 1 or higher. A time-out value of 0 is a special case. In this case there is no time-out and the keyboard
can only be unlocked by means of an unlock-command (LM-command). See also paragraphs 2.1.2 (LM-command) and 2.1.22 (WD-
command) of the commtax2 manual. The time is given in seconds with an accuracy of 1 sec. The allowed value goes from 0 (min) to
255 (max).
0-255
400
Time out from trip start to accept forfait price.
0 - 65535
from Q 401 / Available for any possible software extension / to Q 402
403
Key bitmap enabled while the keyboard is blocked by overspeed
No / Yes
404
Tariff number to which are des! nated all sta! s! cal memories calculated by the current block
0-6
405
Min. distance (in meters) which allows the trip to be saved (if less, tripp will be not considered)
0-255
406
Speed to block the keyboard of the taximeter: this is the speed above which the keyboard of the taximeter gets locked. As soon as the
speed becomes less than this threshold the keyboard gets unlocked again. Normally the value programmed here is a low speed like for
example 10 Km/h. The speed is given in Km/h with an accuracy of 1 Km/h. The allowed value goes from 0 (min) to 255 (max). The value
0 is a special case. It means: disabled.
0-255
407
Speed to block the coun! ng of the tariff : this is the speed above which the taximeter stops counting the tariff. As soon as the speed
becomes less than this threshold the taximeter continues counting the tariff again. Normally the value programmed here is a high speed
like for example 140 Km/h. The speed is given in Km/h with an accuracy of 1 Km/h. The allowed value goes from 0 (min) to 255 (max).
The value 0 is a special case. It means: disabled.
0-255
408
Block number if from Stopped back to Hired: this is the number of the block that will be used when passing from Stopped back to Hired.
The allowed value goes from 0 (min) to 62 (max).
0 – 62
409
Block number if from Stopped to ForHire: this is the number of the block that will be used when passing from Stopped to ForHire.
The allowed value goes from 0 (min) to 62 (max).
0 - 62
OTHER SETTINGS
410
Number of next block with key F2 delayed: this is the number of the next tariff-block to be used when key F2 is kept pressed for about a
second. The allowed value goes from 0 (min) to 62 (max).
0 - 62
411
Distance for autotest: this is the distance with which the vehicle is calibrated. The distance is given in metres with an accuracy of 1
metre. The allowed value goes from 0 (min) to 9999 (max).
0 - 9999
metres
412
Sta! s! cal memories chosen to be print ed out (value 0= print all from 1 to 16)
1-65535
413
Sta! s! cal memories chosen to be print ed out (value 0= print all from 17 to 32)
1-65535
414
Sta! s! cal memories chosen to be print ed out (value 0= print all from 32 to 45)
1-8191
from Q 415 / Available for any custom parameter / to Q 423
To Next Page
Loading...