DSE8610 Control & Instrumentation System Operators Manual
4
3.13.2
CABLE TIE FIXING POINTS .................................................................................. 34
3.13.3
SILICON SEALING GASKET ................................................................................. 34
3.14
APPLICABLE STANDARDS ..................................................................................... 35
3.14.1
ENCLOSURE CLASSIFICATIONS ......................................................................... 36
IP CLASSIFICATIONS ...................................................................................................... 36
NEMA CLASSIFICATIONS ............................................................................................... 37
4
INSTALLATION ............................................................................................. 38
4.1
TERMINAL DESCRIPTION........................................................................................... 38
4.1.1
DC SUPPLY, FUEL AND START OUTPUTS ......................................................... 38
4.1.2
ANALOGUE SENSORS ......................................................................................... 39
4.1.3
MAGNETIC PICKUP, CAN AND EXPANSION ....................................................... 40
4.1.4
LOAD SWITCHING AND GENERATOR VOLTAGE SENSING .............................. 41
4.1.5
BUS SENSING ....................................................................................................... 41
4.1.6
GENERATOR CURRENT TRANSFORMERS ........................................................ 42
4.1.7
CONFIGURABLE DIGITAL INPUTS ....................................................................... 44
4.1.8
PC CONFIGURATION INTERFACE CONNECTOR ............................................... 44
4.1.9
RS485 CONNECTOR ............................................................................................. 45
4.1.10
RS232 CONNECTOR ............................................................................................. 45
4.2
TYPICAL WIRING DIAGRAMS ..................................................................................... 46
4.2.1
3 PHASE, 4 WIRE WITH RESTRICTED EARTH FAULT PROTECTION ............... 47
4.2.2
3 PHASE, 4 WIRE WITHOUT EARTH FAULT PROTECTION ............................... 48
4.2.3
3 PHASE 4 WIRE WITH UNRESTRICTED EARTH FAULT PROTECTION ........... 49
4.2.4
EARTH SYSTEMS ................................................................................................. 50
NEGATIVE EARTH........................................................................................................... 50
POSITIVE EARTH ............................................................................................................ 50
FLOATING EARTH ........................................................................................................... 50
4.3
ALTERNATIVE TOPOLOGIES ..................................................................................... 51
4.3.1
SINGLE PHASE WITH RESTRICTED EARTH FAULT ........................................... 51
4.3.2
SINGLE PHASE WITHOUT EARTH FAULT........................................................... 52
4.3.3
2 PHASE (L1 & L2) 3 WIRE WITH RESTRICTED EARTH FAULT ......................... 53
4.3.4
2 PHASE (L1 & L2) 3 WIRE WITHOUT EARTH FAULT ......................................... 54
4.3.5
2 PHASE (L1 & L3) 3 WIRE WITH RESTRICTED EARTH FAULT ......................... 55
4.3.6
2 PHASE (L1 & L3) 3 WIRE WITHOUT EARTH FAULT MEASURING ................... 56
4.4
TYPICAL ARRANGEMENT OF DSENET® .................................................................. 57
5
DESCRIPTION OF CONTROLS .................................................................... 58
5.1
DSE8610 AUTOSTART CONTROL MODULE.............................................................. 58
5.2
QUICKSTART GUIDE................................................................................................... 60
5.2.1
STARTING THE ENGINE....................................................................................... 60
5.2.2
STOPPING THE ENGINE ...................................................................................... 60
5.3
VIEWING THE INSTRUMENT PAGES ......................................................................... 61
5.3.1
STATUS ................................................................................................................. 62
5.3.2
CONFIGURABLE EDITOR SCREENS ................................................................... 63
5.3.3
ENGINE ................................................................................................................. 64
5.3.4
GENERATOR......................................................................................................... 65
5.3.5
BUS........................................................................................................................ 65
5.3.6
RS232 SERIAL PORT ............................................................................................ 66
5.3.7
RS485 SERIAL PORT ............................................................................................ 69
5.3.8
ABOUT ................................................................................................................... 70
ETHERNET PAGES ......................................................................................................... 70
DATA LOGGING PAGES ................................................................................................. 71
5.3.9
CAN ERROR MESSAGES ..................................................................................... 72
5.4
VIEWING THE EVENT LOG ......................................................................................... 73
5.5
USER CONFIGURABLE INDICATORS ........................................................................ 74
5.6
CONTROLS .................................................................................................................. 75
START .............................................................................................................................. 75
6
OPERATION .................................................................................................. 77
6.1
ALTERNATIVE CONFIGURATIONS ............................................................................ 77
6.2
DUMMY LOAD / LOAD SHEDDING CONTROL ........................................................... 78
6.2.1
DUMMY LOAD CONTROL ..................................................................................... 78
6.2.2
LOAD SHEDDING CONTROL ................................................................................ 79
To Next Page
Loading...
