Name: ELTRA CS-2000
Brand: ELTRA
Rating: 5 (1 reviews)

To Next Page

To Previous Page

Installation

• Normal operation temperature for the resistance furnace is 1350°C.

4.7 Gas purification furnance connecting (optional)

CAUTION

C4.0076

Scalding/burns

Hot furnace / combustion tube / analyzer parts

 Parts of the analyzer can be very hot.

• Use heat protecting gloves.

Fig.

: the gas purification furnace

The tube from the pressure regulator is connected to the lower fitting of the gas purification

furnace (optional), and the tube (1) is connected on its place. See above diagram.

Table of Contents3
Contact Information6
Notes on the Manual6
Explanations of the Safety Instructions7
General Safety Instructions9
Explanation of Signs and Symbols10
Packaging, Transport and Installation11
Packaging11
Transport11
Intended Use11
Conditions for the Installation Site11
Type Plate Description13
Installation14
Setting Check up14
Front Panel Illustration15
Mains Power Connections17
Data Interface18
Gas Connections19
Resistance Furnace-Temperature Adjustment20
Gas Purification Furnance Connecting (Optional)21
Autoloader (Optional)22
Analysis23
Working Procedure23
Resistance Furnace24
Induction Furnace26
Analysis Example27
Combustion Peak27
Combustion Double Peak27
Work Breaks28
Crucibles Preheating28
Operating the Pre-Heating Furnace (Optional)29
TIC-Determination (Optional)30
TIC-Module30
TIC Analysis30
TIC-Module Operation Procedure32
Applications33
Induction Furnace33
Resistance Furnace37
Coal Analysis37
Oil, Plastics, Asphalt and Rubber Analysis37
Ash Analysis38
Graphite Analysis39
Calcium Carbonate Analysis39
Limestone Analysis39
Cement Analysis39
Gypsum and Desulfurization Products (from Power Plants) Analysis39
Low Carbon Analysis39
Maintenance43
General Information43
Resistance Furnace Operation43
Induction Furnace Operation43
Reagent Tubes - Removing and Installing44
Reagent Tubes Filling47
Chemicals47
Reagent Tube Filling-Induction Furnace49
Reagent Tube Filling-Resistance Furnace52
Oxygen Purification Furnace Quartz Tube Filling (Optional)54
Halogen Trap Filling (Optional)55
Paper Filter Changing57
Dust Filter Cartridge Replacing57
O-Rings Replacement58
Replacing the O-Rings 11 and 12 for Combustion Tube60
Replacing the O-Ring 13 for Lower Furnace Lock60
Replacing the O-Rings for Furnace Seal61
Furnace Cleaning Brush - Replacing64
Dust Trap Cleaning65
Dust Trap Cleaning-Induction Furnace65
Dust Trap Cleaning-Resistance Furnace68
Combustion Tube Replacement69
Induction Furnace70
Resistance Furnace72
Generator Tube Replacing74
Combustion Coil Replacing74
Pedestal Removing74
Heating Elements Replacing75
Gas Leaks Checking76
Leaks in the Furnace Inlet System77
Leaks in the Furnace77
Leaks in the Furnace Outlet System77
Function Description78
System Overview78
Measuring Principle78
Gas Flow System79
Infrared Cell81
Furnace82
Induction Furnace82
Resistance Furnace83
Miscellaneous85
Ordering Numbers85
Front Side85
Left Hand Side86
Right Side87
Pneumatics88
Oscillating Circuit89
Furnace91
Furnace Cleaning Mechanism93
Gas Purification Furnace94
Front Side and Rear Side95
Restistance Furnace Details95
Furnace Tube Cleaning97
Tic-Module98
Packing100
Pre-Installation Guide103
Approved Methodologies to Which Eltra Instruments Conform105
Inorganic Materials (Metals)105
Organic Materials (Oil, Coal, Foodstuffs)106
Disposal106
Index108

Other manuals for ELTRA CS-2000

Service Manual160 pages

Questions and Answers:

Need help?

Do you have a question about the ELTRA CS-2000 and is the answer not in the manual?

ELTRA CS-2000 Specifications

General

Brand	ELTRA
Model	CS-2000
Category	Measuring Instruments
Language	English

Related product manuals

ELTRA CS-800

158 pages

ELTRA ELEMENTRAC CS-i

ELTRA ELEMENTRAC ONHp2

96 pages

ELTRA CS-2000 Manual

Table of Contents

Other manuals for ELTRA CS-2000

Questions and Answers:

ELTRA CS-2000 Specifications

Related product manuals