Contents Proline Prowirl 72 FOUNDATION Fieldbus
4 Endress + Hauser
10.1.10Frequency ranges for air and water . . . . . . 71
10.1.11Mechanical construction . . . . . . . . . . . . . . 73
10.1.12Human interface . . . . . . . . . . . . . . . . . . . . 74
10.1.13Certificates and approvals . . . . . . . . . . . . . 74
10.1.14Ordering information . . . . . . . . . . . . . . . . 76
10.1.15Accessories . . . . . . . . . . . . . . . . . . . . . . . . 76
10.1.16Documentation . . . . . . . . . . . . . . . . . . . . 76
10. 2 Dimensions of flow conditioner . . . . . . . . . . . . . . 77
11 Operation via
FOUNDATION Fieldbus . . . . . . . . . . 80
11. 1 Block model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
11. 2 Resource Block (device block) . . . . . . . . . . . . . . . . 81
11.2.1 Selecting the operating mode . . . . . . . . . . 81
11.2.2 Block status . . . . . . . . . . . . . . . . . . . . . . . 82
11.2.3 Write protection and simulation . . . . . . . . 82
11.2.4 Alarm detection and processing . . . . . . . . 82
11.2.5 Resource Block parameters . . . . . . . . . . . . 83
11. 3 Transducer Block . . . . . . . . . . . . . . . . . . . . . . . . . 84
11.3.1 Block output variables . . . . . . . . . . . . . . . 85
11.3.2 Selecting the operating mode . . . . . . . . . . 86
11.3.3 Alarm detection and processing . . . . . . . . 86
11.3.4 Accessing the manufacturer-specific
parameters . . . . . . . . . . . . . . . . . . . . . . . . 86
11.3.5 Selecting the units . . . . . . . . . . . . . . . . . . 86
11. 4 FOUNDATION Fieldbus parameters . . . . . . . . . . . 87
11. 5 Endress+Hauser parameters:
Transducer Block "Flow" . . . . . . . . . . . . . . . . . . . 89
11. 6 Endress+Hauser parameters:
Transducer Block "Totalizer" . . . . . . . . . . . . . . . . 103
11. 7 Endress+Hauser parameters:
Transducer Block "Display" . . . . . . . . . . . . . . . . . 107
11. 8 Endress+Hauser parameters:
Transducer Block "Diagnosis" . . . . . . . . . . . . . . . 112
11. 9 Endress+Hauser parameters:
Transducer Block "Service" . . . . . . . . . . . . . . . . . 114
11. 10 Analog Input Function Block . . . . . . . . . . . . . . . 114
11.10.1Signal processing . . . . . . . . . . . . . . . . . . 114
11.10.2Selecting the operating mode . . . . . . . . . 116
11.10.3Selecting the process variable . . . . . . . . . 116
11.10.4Linearization types . . . . . . . . . . . . . . . . . 116
11.10.5Selecting the units . . . . . . . . . . . . . . . . . 116
11.10.6Status of the output value OUT . . . . . . . . 117
11.10.7Simulation of input/output . . . . . . . . . . . 117
11.10.8Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . 117
11.10.9Rescaling the input value . . . . . . . . . . . . 118
12 Discrete Output Function Block . . . . 119
12. 1 Assignment: Discrete Output Function
Block/Transducer Blocks . . . . . . . . . . . . . . . . . . 119
12. 2 Values for the CAS_IN_D, RCAS_IN_D,
OUT_D, and SP_D parameters . . . . . . . . . . . . . . 119
13 Factory settings . . . . . . . . . . . . . . . . 121
13. 1 Metric system units (not for USA and Canada) . . 121
13. 2 US units (only for USA and Canada) . . . . . . . . . . 122
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
To Next Page
Loading...
