To Next PageTo Next Page
Need help?Do you have a question about the enorossi BF and is the answer not in the manual?
Explains the purpose and importance of reading the manual before use.
Defines warning symbols (Important, Attention, Danger, Note) used in the manual.
Details the identification plate and CE mark requirements for the equipment.
Lists conditions under which the warranty is not recognized.
Addresses equipment compliance with regulations outside the EU.
General safety rules to be observed when using the mower.
Safety guidelines for moving, installing, and handling the equipment.
Requirements for rear dimensions, signs, and reflective elements for road travel.
Ensuring tractor's signaling and visibility are adequate for road travel.
Adhering to weight limits and moderate speeds for safe operation.
Importance of knowing and following local road traffic regulations.
Describes the mower's agricultural purpose for cutting forage.
Essential checks and verifications before starting operation.
Verifying correct installation and safety of the cardan shaft.
Ensuring the tractor PTO is disengaged and set correctly.
Performing daily maintenance as described in the manual.
Warning against using equipment with broken or damaged protective parts.
Guidelines for gently lowering the equipment to avoid damage.
Identifying and avoiding dangerous zones during operation.
Maintaining speed and never leaving the tractor unattended while running.
Actions for operators during work breaks, including disengaging PTO and securing the tractor.
Precautions to take before reversing the tractor with the mower attached.
Information on mower noise and the need for tractor noise protection.
Conditions requiring immediate cessation of work.
Managing vibrations through proper lubrication of transmission parts.
Outlines improper uses and modifications that void warranty and liability.
Recommendations for operating in low visibility conditions (fog, dust, rain).
Actions to take if a person or animal enters a dangerous zone.
Situations where the mower must not be used, like damp forage or stony ground.
Lists specific actions or conditions for which the operator is responsible for damages.
Explains the meaning of different shapes and colors of safety labels.
Forbids adjustments, lubrication, or repairs on moving components.
Strictly prohibits entering or moving within the operating area while the mower is active.
Mandates reading the use and maintenance manual before any intervention.
Warns against approaching cutting blades when they are in operation.
Advises checking PTO speed and rotation to prevent gear damage.
Forbids removing protective covers, especially belt guards.
Warns against adjusting or replacing belts while the equipment is operating.
Emphasizes the need to replace illegible or missing safety labels and pictograms.
Discusses noise levels and the limited need for operator acoustic protection for the mower itself.
Identifies residual risk of loss of stability when parking due to missed foot rest installation.
Requirements and prerequisites for installing the mower on tractors.
Step-by-step guide for attaching the mower to the tractor.
How to mark the chain for consistent operating height in future installations.
Specific steps for mechanical models to install and adjust the cutting bar chain.
Explains the function of the compensation spring and its adjustment.
How to connect hydraulic piping for hydraulic models.
Refers to manual for cardan shaft installation and PTO verification.
Instructions for removing the mower from the tractor.
Recommendations for safely storing the mower when not in use.
Essential checks and preparations before starting work.
Steps to convert the mower from transport to working configuration.
Specific steps for hydraulic models, including rod and tap adjustments.
How to tension transmission belts for proper operation.
Calibrating hydraulic flow valves for descent and ascent speed.
Instructions on starting the tractor and engaging the PTO safely.
Recommends speed for efficient grass discharge and avoiding clogging.
Reiterates observing safety precautions during the working process.
Warning against mowing in stony or rocky areas.
Explains the function of the safety device and actions if it activates.
Lifting the cutting bar for mechanical models for directional changes.
How to adjust the cutting height using the tie-rod.
Adjusting hydraulic valves to control cutting bar descent/ascent speed.
Step-by-step guide for adjusting hydraulic valves one at a time.
How to check and verify the tension of the transmission belts.
Recommends loosening transmission belts during long periods of inactivity.
Putting the mower into transport configuration before moving after work.
Operator must be adult, qualified, and trained for maintenance tasks.
Requirements for a safe and clear work area for maintenance.
Absolutely forbidden to perform maintenance with the tractor engine running or mower operating.
Recommends posting a "Barra falciante in riparazione" sign to prevent accidental startup.
Emphasizes reading the manual and following safety rules for all maintenance.
Indicates that maintenance frequencies are indicative and may vary with usage conditions.
Lists periodic checks and tasks with their recommended intervals.
Specific procedure for cleaning and oiling the cutters, including safety distances.
Steps for cleaning the mowing bar with pressurized water, maintaining safety distance.
How to adjust and restore correct connection of blade guides due to wear.
Steps to remove the blade-holding bar from the mower.
Verifying correct connection of tooth-holding bar and blade guide, adjusting shims if needed.
Steps for removing and installing new blades, including rivet types.
Procedure for replacing damaged teeth on BFS model mowers.
Steps for replacing worn or broken belts, recommending replacement of all belts.
Replacing protective cover and restoring belt tension after pulley replacement.
Procedures for removing and installing new pulleys and belts.
Instructions for lubricating grease nipples with the recommended grease type.
Important note on proper disposal of oils, lubricants, and other harmful materials.
Common issues with the hydraulic system (jerky movement, control issues) and their solutions.
Guidelines for the disposal of materials when the mower is scrapped.
General| Brand | enorossi |
|---|---|
| Model | BF |
| Category | Lawn Mower |
| Language | English |
