ETC Sensor3 CEM3 - AF Load and Dimmer Overtemp Errors

CEM3 Menu Flow Chart 53
Note:
Note:
Note:
Temp High Warn
is in Fahrenheit (F) or Celsius (C)
depending on the Temp Locale
setting in
Setup/UI Preferences.
Rack #1 - CEM3 Rack
System OK
DMX A: Off DMX B: Off
sACN: 1/1
[Quick S etup] [Info]
Rack #1 - CEM3 Rack
System OK
DMX A: Off DMX B: Off
sACN: 1/1
[Quick S etup] [Info]
Setup
[Dimmers]
[Rack]
[Circuit Assignment]
[Patching]
[Network]
[File Operations]
[Panic]
[Time/Date]
[Quick Setup]
[UI Preferences]
Rack Setup
Rack Number: [1]
System Number: [1]
Data Ports:
DMX A: [Disabled]
DMX B: [Disabled]
sACN: [Enabled]
Arch Priority: [100]
Off as Release:[Yes]
Fan: [30]
AF Enabled: [Yes]
Presets on Boot: [N]
Setup at Home: [Yes]
Volt High Warn:[140]
Temp High Warn:[149]
Station Power: [Off]
Remote Record: [No]
[Data Loss Behavior]
Rack #1 - CEM3 Rack
System OK
DMX A: Off DMX B: Off
sACN: 1/1
[Quick S etup] [Info]
Reboot Required
This operation will
cause your CEM3 to
reboot.
Do you want to
continue?
[No]
[Yes]
Rack #1 - CEM3 Rack
System OK
DMX A: Off DMX B: Off
sACN: 1/1
[Quick S etup] [Info]
Rack Setup
Rack Number: [1]
System Number: [1]
Data Ports:
DMX A: [Disabled]
DMX B: [Disabled]
sACN: [Enabled]
Arch Priority: [100]
Off as Release:[Yes]
Fan: [30]
AF Enabled: [Yes]
Presets on Boot: [N]
Setup at Home: [Yes]
Volt High Warn:[Yes]
Temp High Warn:[Yes]
Station Power: [Off]
Remote Record: [No]
[Data Loss Behavior]
Rack #1 - CEM3 Rack
System OK
DMX A: Off DMX B: Off
sACN: 1/1
[Quick S etup] [Info]
Data Loss Behavior
DMXA: [Crossfade]
Fade Time: [2]
Wait Time: [180]
Preset Space: [1]
Preset Number: [16]
DMXB: [Wait & Fade]
Fade Time: [2]
Wait Time: [180]
sACN: [Wait & Fade]
Fade Time: [2]
Wait Time: [180]
Rack #1 - CEM3 Rack
System OK
DMX A: Off DMX B: Off
sACN: 1/1
[Quick S etup] [Info]
Setup
[Dimmers]
[Rack]
[Circuit Assignment]
[Patching]
[Network]
[File Operations]
[Panic]
[Time/Date]
[Quick Setup]
[UI Preferences]
Circuit Assignment
[Auto Assign...]
[Edit Circuit Layout]
Auto Ckt Assignment Confirmation
You have selected to
renumber all dimmers
in the rack.
Are you sure you
want to do this?
[No!] [Yes/Renumber]
Auto Ckt Assignment
Numbering: [Straight]
First Circuit: [1]
[Cancel] [Renumber]
Numbering: [Straight]
First Circuit: [1]
Space: [1]
[Cancel] [Renumber]
Confirmation
You have selected to
renumber all dimmers
in the rack.
Are you sure you
want to do this?
[No!] [Yes/Renumber]
Circuit Assignment
[Auto Assign...]
[Edit Circuit Layout]
Circuit Setup
Lug Sp Ckt Type
1 - - AFM
2 - - AFM
3 1 1 D20AF
4 1 2 D20AF
5 1 3 D20
6 1 4 D20
A T T E N T I O N !
Save Network Settings
Before Exiting?
[No/Cancel]
[Yes/Save]
[Continue Editing]
A T T E N T I O N !
Save Network Settings
Before Exiting?
[No/Cancel]
[Yes/Save]
[Continue Editin g]
A T T E N T I O N !
Save Network Settings
Before Exiting?
[No/Cancel]
[Yes/Save]
[Continue Editin g]
Duplicate Numbers
Duplicate Space /
circuit numbers found
Please correct or
discard your changes
[Go Back] [Abort]
Duplicate Numbers
Duplicate Space /
circuit numbers found
Please correct or
discard your changes
[Go Back] [Abort]
Module choices vary by
rack type.
Duplicate numbers screen is
only shown if there are
duplicate space or circuit
numbers other than 0.