Extron electronics XTP II CrossPoint Series User Manual

Align with
Plastic Guides
Captive Screws
I
N
P
U
T
S
O
U
T
P
U
T
S
LAN
ACT
LINK
RESET
100-240V
50-60Hz
--A MAX
REMOTE
RS 232/RS422
DISCONNECT POWER
CORD BEFORE
SERVICING
IN
XTP CP 4i VGA
AUDIO
LRLRLR LR
IN
IN
XTP CP 4i VGA
AUDIO
LRLRLR LR
IN
IN
IN
XTP CP 4i
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
IN
IN
XTP CP 4i
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
OUT
OUT
XTP CP 4o
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
OUT
OUT
XTP CP 4o
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
RS-232 IR
TxRx TxRx
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
OUT
XTP CP 4o SA
AUDIO
LRLRLR LR
OUT
IN
XTP CP 4i DVI Pro
AUDIO
LRLRLR LR
IN
IN
XTP CP 4i DVI Pro
AUDIO
LRLRLR LR
IN
OUT
XTP CP 4o DVI Pro
AUDIO
LRLRLR LR
OUT
OUT
XTP CP 4o DVI Pro
AUDIO
LRLRLR LR
OUT
IN
XTP CP 4i HDMI
AUDIO
LRLRLR LR
IN
IN
XTP CP 4i HDMI
AUDIO
LRLRLR LR
IN
OUT
XTP CP 4o HDMI
AUDIO
LRLRLR LR
OUT
OUT
XTP CP 4o HDMI
AUDIO
LRLRLR LR
OUT
Align with
Plastic Guides
IN
XTP CP 4i HDMI
AUDIO
L R
L R
L R
L R
IN
Captive Screws
XTP II CrossPoint 3200 XTP II CrossPoint 1600
(XTP II CrossPoint 6400 similar)
Figure 75. Input or Output Board Replacement
Installing an Input or Output Board or Blank Panel
IN
IN
Install an input or output board or blank panel as follows:
1. For an input or output board, orient the board to be installed so
that the silk-screened word “In” or “Out” is right-side up and to the
top (XTP II CrossPoint 3200 or XTP II CrossPoint 6400) or to the left
(XTP II CrossPoint 1600) (see figure 76).
OUT
OUT
Figure 76. Board Orientation
2. For an input or output board, align the board with the top and bottom
(XTP II CrossPoint 3200 or XTP II CrossPoint 6400) or left and right
(XTP II CrossPoint 1600) chassis guides (see figure 75).
3. Gently slide the board or blank panel into the enclosure. For an input or output
board, slide the board toward the front panel until it meets resistance.
4. Gently seat the board or panel in the backplane.
5. Use a screwdriver to tighten the captive screws that lock the board or panel in place.
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Maintenance and Modifications 145

Extron electronics XTP II CrossPoint Series Specifications

General

Brand	Extron electronics
Model	XTP II CrossPoint Series
Category	Matrix Switcher
Language	English