Feig Electronic TST FUZ2-C User Manual

ATTENTION!
IMPORTANT SAFETY
INFORMATION
The specifications of
these instructions
require compliance to
ensure personal safety.
Store these instructions
safely.
Original operating instructions
TST FUZ2
Variants
-A / -B / -C /
-CX / -G / -L
DE
ACHTUNG! WICHTIGE SICHERHEITSANWEISUNGEN!
Den Hinweisen auf Seite 2 dieser Montageanleitung ist Folge zu leisten.
EN
ATTENTION! IMPORTANT SAFETY INFORMATION!
Follow the instructions on page 2 of this manual.
FR
ATTENTION! IMPORTANTES INDICATIONS DE SÉCURITÉ!
Les instructions de la page 2 de cette notice de montage doivent être
observées strictement,
NL
LET OP! BELANGRIJKE VEILIGHEIDSINSTRUCTIES!
Volg de instructies op pagina 2 van deze montagehandleiding op.
IT
ATTENZIONE! INDICAZIONI SULLA SICUREZZA IMPORTANTI!
Prestare attenzione alle note alla pagina 2 delle presenti istruzioni di
montaggio.
ES
ATENCIÓN INDICACIONES IMPORTANTES DE SEGURIDAD!
Deben seguirse las indicaciones detalladas en página 2 de estas
instrucciones de montaje.
DA
PAS PÅ! VIGTIGE SIKKERHEDSANVISNINGER
Oplysningerne på side 2 i denne monteringsvejledning skal følges.
Assembly instructions
Installation, commissioning, utilization and maintenance

Feig Electronic TST FUZ2-C Specifications

General

Housing Material	Plastic
Protection Class	IP 65
Operating Temperature	-20°C to +55°C
IP Rating	IP65
Communication Interface	RS232, RS485

Summary

Important Safety Information

User Login and Authentication

Login Credentials and Recovery

Basic Settings Configuration

Automatic Basic Data Query

Procedure for automatic controller parameter query.

Motor Data Configuration

Setting motor parameters based on nameplate data for optimal operation.

General Description and Intended Use

Intended Use

Defines the controller's purpose, application context, and compliance requirements.

Incorrect Use

Details prohibited uses and potential liabilities for misuse or alteration.

Target Group and Personnel Qualification

Target Group Definition

Personnel Qualification Requirements

Specifies the necessary training and authorization for personnel working with the controller.

Duty of Care of the Operating Company

Safety Instructions and Warnings

General Safety Warnings

Highlights potential risks from failure to observe safety advisories.

Safety Functions per EN 12453:2017

Connection Example Testing

Demonstrates testing procedures, e.g., using a transmitter-receiver light barrier.

Safety Function Parametrization

Configuration steps for input and output parameters for function testing.

Controller Installation Procedures

Safe Installation Instructions

Critical instructions for safe controller installation to prevent injuries.

Mounting Control Electronics

Mounting Board in Steel Housing

Electrical Connection Procedures

General Electrical Connection Safety

Crucial safety precautions for wiring, testing, and maintenance.

Pre-Power-On Checks

Essential checks before first power-on and after wiring completion.

Power Supply Without Main Switch

Power Supply With Main Switch

Motor and Brake Connection

Motor Cable Shielding Connection

Instructions for connecting motor cable shielding to PE terminal and EMC bracket.

Safety Edge Integration

Optical Safety Edge Connection

Wiring diagram for connecting an optical safety edge.

Electrical Resistance Safety Edge Connection

Second Safety Edge Evaluation

Optical Safety Edge for Input 10

Connection diagram for optical safety edge on input 10.

Electrical Resistance Safety Edge for Input 10

Digital Input Connection

Light Curtain TST LGB Installation

TST LGB Connection Diagram

Limit Switch Connection Options

Absolute Encoder TST PE/FSB with WICAB

Connection details for TST PE/FSB absolute encoders with WICAB system.

Absolute Encoder TST PD Connection

Absolute Encoder DES Connection

Mechanical Limit Switch Connection

Photo Eye Connection

External Triggering Device Connections

Overview of Controller Outputs

Overview of Controller Inputs

Expansion Card RFUxK Features

Interface Card TST RFUxFCOM

Expansion Board TST RFUxIO-B/-E

General Operating Instructions for Parameters

Accessing Parameter Operation Mode

Steps to enter parameter operation mode using DIP switch and keys.

Editing Selected Parameters

Exiting Parameter Operation Mode

Executing a Controller Reset

Extended Parameter Configuration Mode

Controller Commissioning

Pre-Commissioning Checks

Essential checks before controller commissioning, including connections and safety devices.

Commissioning with Absolute/Incremental Encoder

Step-by-step guide for commissioning using absolute or incremental encoders.

Commissioning with Mechanical Limit Switches

Commissioning with Light Curtain TST LGB

TST LGB Installation Guide

Instructions for mounting the light curtain according to TST LGB manual.

Re-teaching End Positions

Boost for Low Speed Performance

Movement Optimization

Door Opening Optimization

Illustrates and explains door opening movement using the frequency converter.

Door Closing Optimization

Pre-Limit Switch Setting

Ramp Configuration for Speed Control

Correction of Final Positions

Controller Messages and Errors

Error Message Troubleshooting

Lists error codes, descriptions, and possible reasons for faults.

General Messages and Codes

General Input Signals

Safety and Emergency Stop Chain Inputs

Inputs related to safety circuits and emergency stop functions.

Safety Edge Input Signals

Technical Specifications

Controller Input Specifications

Safety Edge Input Specifications

Relay Output Specifications

Drive Output Specifications (Variants B, C, CX, CGH, CXGH, LGH)

Protection Type and Class