Flexim FLUXUS WD200 - User Manual

106 pages

Save Page as PDF

To Next Page

User Manual

UMFLUXUS_F5WDV1-1EN

Ultrasonic Flowmeter

for Water

FLUXUS WD100

FLUXUS WD200

Main Page

Default Chapter4
- Umfluxus_F5Wdv1-1En, 20164
- Table of Contents5
- Umfluxus_F5Wdv1-1En, 20168
1 Introduction9
- Regarding this User Manual9
- Safety Instructions9
- Warranty9
2 Handling10
- First Inspection10
- General Precautions10
- Cleaning10
3 General Principles11
- Measurement System11
- Measurement Principle11
- Measurement Arrangements14
4 Description of the Transmitter16
- Keyboard16
5 Selection of the Measuring Point17
- Acoustic Penetration17
- Undisturbed Flow Profile19
- Selection of the Measurement Arrangement Taking into Account the Measuring Range and the Measuring Conditions21
- Selection of the Sound Beam Plane Near an Elbow22
6 Installation of the Transmitter23
- Location23
- Connection of the Transducers25
- Connection of the Power Supply31
- Connection of the Outputs32
7 Installation of the Transducers33
- Preparation of the Pipe33
- Orientation of the Transducers and Transducer Distance33
- Installation with Variofix C33
8 Start-Up of the Transmitter40
- Switching on40
- Initialization40
- Display40
- Hotcodes42
- Language Selection43
- Interruption of the Power Supply43
9 Basic Measurement44
- Input of the Pipe Parameters44
- Input of the Fluid Parameters45
- Extension Cable45
- Input of the Measuring Point Number46
- Defining the Number of Sound Paths46
- Transducer Distance46
- Start of the Measurement48
- Detection of the Flow Direction48
- Interruption of the Measurement48
10 Displaying the Measured Values49
- Selection of the Physical Quantity and the Unit of Measurement49
- Adjustment of the Display49
- Status Line50
- Transducer Distance51
11 Advanced Measuring Functions52
- Command Execution During Measurement52
- Damping Factor52
- Totalizers52
- Upper Limit of the Flow Velocity54
- Cut-Off Flow54
- Uncorrected Flow Velocity55
- Change of the Limit for the Inner Pipe Diameter55
- Program Code55
12 Data Logger and Transmission of Data57
- Data Logger57
- Transmission of Data60
13 Settings65
- Time and Date65
- Dialogs and Menus65
- Measurement Settings68
- Setting the Contrast68
- Instrument Information68
14 Superuser Mode69
- Activation/Deactivation69
- Defining the Flow Parameters69
- Limit of the Signal Amplification71
- Upper Limit of the Sound Speed71
- Detection of Long Measurement Failures71
- Number of Decimal Places of the Totalizers72
- Manual Reset of the Totalizers72
- Display of the Sum of the Totalizers73
- Display of the Last Valid Measured Value73
- Display During the Measurement73
15 Outputs74
- Installation of an Output74
- Error Value Delay77
- Activation of an Analog Output77
- Activation of a Binary Output as a Pulse Output79
- Activation of a Binary Output as an Alarm Output79
- Behavior of the Alarm Outputs81
- Deactivation of the Outputs83
16 Troubleshooting84
- Problems with the Measurement84
- Selection of the Measuring Point85
- Maximum Acoustic Contact85
- Application Specific Problems85
- Large Deviations of the Measured Values86
- Problems with the Totalizers86
- Data Transmission86
A Menu Structure87
B Units of Measurement95
C Reference100
D Declarations of Conformity103

Need help?

Do you have a question about the Flexim FLUXUS WD200 and is the answer not in the manual?

Flexim FLUXUS WD200 Specifications

General

Brand	Flexim
Model	FLUXUS WD200
Category	Measuring Instruments
Language	English

Related product manuals

Flexim FLUXUS ADM F705

87 pages

Flexim FLUXUS ADM 8027

160 pages

Flexim FLUXUS F60 Series

244 pages

Flexim FLUXUS F808 A1 Series

186 pages

Flexim FLUXUS F809 A1 Series

186 pages

Flexim FLUXUS ADM 5 07 Series

87 pages

Flexim FLUXUS WD200 - User Manual

Table of Contents

Flexim FLUXUS WD200 Specifications

Related product manuals