Flexim FLUXUS WD200 - Default Chapter; Umfluxus_F5 Wdv1-1 En, 2016

106 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

FLUXUS WD100, WD200

UMFLUXUS_F5WDV1-1EN, 2016-04-08

Table of Contents

Default Chapter4
- Umfluxus_F5Wdv1-1En, 20164
- Table of Contents5
- Umfluxus_F5Wdv1-1En, 20168
1 Introduction9
- Regarding this User Manual9
- Safety Instructions9
- Warranty9
2 Handling10
- First Inspection10
- General Precautions10
- Cleaning10
3 General Principles11
- Measurement System11
- Measurement Principle11
- Measurement Arrangements14
4 Description of the Transmitter16
- Keyboard16
5 Selection of the Measuring Point17
- Acoustic Penetration17
- Undisturbed Flow Profile19
- Selection of the Measurement Arrangement Taking into Account the Measuring Range and the Measuring Conditions21
- Selection of the Sound Beam Plane Near an Elbow22
6 Installation of the Transmitter23
- Location23
- Connection of the Transducers25
- Connection of the Power Supply31
- Connection of the Outputs32
7 Installation of the Transducers33
- Preparation of the Pipe33
- Orientation of the Transducers and Transducer Distance33
- Installation with Variofix C33
8 Start-Up of the Transmitter40
- Switching on40
- Initialization40
- Display40
- Hotcodes42
- Language Selection43
- Interruption of the Power Supply43
9 Basic Measurement44
- Input of the Pipe Parameters44
- Input of the Fluid Parameters45
- Extension Cable45
- Input of the Measuring Point Number46
- Defining the Number of Sound Paths46
- Transducer Distance46
- Start of the Measurement48
- Detection of the Flow Direction48
- Interruption of the Measurement48
10 Displaying the Measured Values49
- Selection of the Physical Quantity and the Unit of Measurement49
- Adjustment of the Display49
- Status Line50
- Transducer Distance51
11 Advanced Measuring Functions52
- Command Execution During Measurement52
- Damping Factor52
- Totalizers52
- Upper Limit of the Flow Velocity54
- Cut-Off Flow54
- Uncorrected Flow Velocity55
- Change of the Limit for the Inner Pipe Diameter55
- Program Code55
12 Data Logger and Transmission of Data57
- Data Logger57
- Transmission of Data60
13 Settings65
- Time and Date65
- Dialogs and Menus65
- Measurement Settings68
- Setting the Contrast68
- Instrument Information68
14 Superuser Mode69
- Activation/Deactivation69
- Defining the Flow Parameters69
- Limit of the Signal Amplification71
- Upper Limit of the Sound Speed71
- Detection of Long Measurement Failures71
- Number of Decimal Places of the Totalizers72
- Manual Reset of the Totalizers72
- Display of the Sum of the Totalizers73
- Display of the Last Valid Measured Value73
- Display During the Measurement73
15 Outputs74
- Installation of an Output74
- Error Value Delay77
- Activation of an Analog Output77
- Activation of a Binary Output as a Pulse Output79
- Activation of a Binary Output as an Alarm Output79
- Behavior of the Alarm Outputs81
- Deactivation of the Outputs83
16 Troubleshooting84
- Problems with the Measurement84
- Selection of the Measuring Point85
- Maximum Acoustic Contact85
- Application Specific Problems85
- Large Deviations of the Measured Values86
- Problems with the Totalizers86
- Data Transmission86
A Menu Structure87
B Units of Measurement95
C Reference100
D Declarations of Conformity103

Related product manuals

Preview: Flexim FLUXUS WD

Flexim FLUXUS WD

Preview: Flexim FLUXUS WW

Flexim FLUXUS WW

Preview: Flexim FLUXUS F601

Flexim FLUXUS F601

Preview: Flexim FLUXUS G601

Flexim FLUXUS G601

Preview: Flexim FLUXUS G800

Flexim FLUXUS G800

Flexim FLUXUS F502TE

Flexim FLUXUS ADM F705

Flexim FLUXUS ADM 8027

Preview: Flexim FLUXUS F60 Series

Flexim FLUXUS F60 Series

Preview: Flexim FLUXUS F808 A1 Series

Flexim FLUXUS F808 A1 Series

Flexim FLUXUS F809 A1 Series

Preview: Flexim FLUXUS ADM 5 07 Series

Flexim FLUXUS ADM 5 07 Series