Home
Focus Microwaves
Tuner
ituner
Page 58 (5.5.9 LoadCalibration Method)
Focus Microwaves ituner - 5.5.9 LoadCalibration Method; 5.5.10 SetAdapter and GetAdapter Method
73 pages
Manual
Save Page as PDF
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
iTuner Manual
53
5.5.9
LoadCalibration
Method
Method:
LoadCalibrati
on (calId)
Parameter:
calId [in]
Calibration unique I
D
Return value:
Result value of co
mmand (see co
mmand descripti
on in chapter 4)
Remarks:
LoadCalibration
encapsulat
es the ‘LOADCA
L’ command and
loads the calibrati
on
specified.
Examples:
iTuner.LoadCalibration(
calId)
5.5.10
SetAdapter and GetAda
pter Method
Method:
SetAdapter(s11_
mag, s11_ang,
s12_mag, s12_ang,
s21_mag,
s21_ang, s22_mag
, s22_ang)
GetAdapter(s11_m
ag,
s11_ang, s12_
mag, s12_ang, s21_mag
,
s21_ang, s22_mag
, s22_ang)
Parameter:
s11_mag [in][
out]
s11_ang [in] [out]
s12_mag [in] [out]
s12_ang [in] [out]
s21_mag [in] [out]
s21_ang [in] [out]
s22_mag [in] [out]
s22_ang [in][out]
Linear Magnitude
of s11
Phase of s11 in degre
es
Linear Magnitude
of s12
Phase of s12 in degre
es
Linear Magnitude
of s21
Phase of s21 in degre
es
Linear Magnitude
of s22
Phase of s22 in degre
es
Return value:
Result value of co
mmand (see co
mmand descripti
on in chapter 4)
Remarks:
SetAdapter
encapsul
ates the ‘ADA
PTER’ com
mand.
57
59
Table of Contents
Main Page
Default Chapter
2
Table of Contents
2
1 Introduction
6
System Requirements
6
2 Ip Address Configuration and Connection
7
Setting the Computer Sip Address
7
Single Tuner Tcp/Ip Connection
9
Multiple Tuner Tcp/Ip Connection
14
3 Configuring Load Pull Explorer
15
4 Ituner Command Language
17
Introduction
17
Control Commands
20
Config Command
20
Stop Command
21
Reset Command
22
Disp Command
22
Help Command
23
Rev? Command
23
IP_SET Command
23
IP? Command
23
Positioning Commands
23
Init Command
24
Pos Command
25
Move Command
27
STATUS? Command
27
OPC? Command
28
OPC2? Command
28
Tuning Commands
29
Introduction
29
Tuning and Impedance Query Commands
32
Mode Command
32
Dir Command
33
Loadcal Command
34
Loadfreq Command
34
Freq? Command
35
Adapter Command
36
Term Command
36
Tuneto Command
37
Tunevswr Command
38
Tunepm Command
38
Tuneh1 Command
39
Tuneh2 Command
39
CALPOINT Command
39
CALPOINT? Command
40
Gamma? Command
40
Gamma_At? Command
41
VSWR? Command
41
VSWR_AT? Command
42
Loss? Command
42
SPAR? Command
42
SPAR_AT? Command
43
Dump Command
43
Constant Vswr Commands
44
VSWR_AUTO Command
45
VSWR_INIT Command
45
VSWR_INC Command
46
VSWR_STEP Command
46
VSWR_DO360 Command
46
VSWR_PHASE Command
46
Configuration and Maintenance Commands
47
Watchdog Command
47
ERASE_CAL Command
47
Compact Command
47
Format Command
47
5 Using the Ituner with Itunerx.ocx
48
Registering Itunerx.ocx
48
Programming with Itunerx
49
Blocking Versus Non-Blocking Calls
50
Itunerx Properties
51
Address Property
51
Monitor Property
51
Revision Property
52
Showerror Property
52
Timeout Property
52
Itunerx Methods
53
Send Method
53
Sendcmd Method
54
OPC Method
54
Getstatus Method
55
Initialize and Getinit Method
55
Setposition and Getposition Method
56
Getnbcalibrations Method
57
Getcalibrationinfo Method
57
Loadcalibration Method
58
Setadapter and Getadapter Method
58
Settermination and Gettermination Method
59
Setgamma and Getgamma Method
60
Getgammaat Method
60
Setvswr and Getvswr Method
61
Getvswrat Method
62
Getspar Method
62
Getsparat Method
63
Getlastreply Method
64
Closeconnection Method
64
6 Adding Calibration Data
65
Tuner Calibration
65
Frequency Definition
67
Uploading Calibration Data Using Load Pull Explorer
68
7 Using Iutility
70
File Tab
70
Tuner Tab
71
Setup Tab
72
Operations Tab
73
To Next Page
Loading...