How to remove black lines from Fujitsu Scanner output?
If black lines are produced on the scanned document from your Fujitsu Scanner, especially if the scanned documents are written with a pencil, it is recommended to use Carrier Sheet for scanning. If you are not using the Carrier Sheet for scanning such documents, clean rollers as often as possible.
Why applications cannot be selected in the ScanSnap Manager settings?
If you can't select an application in advance, use Left-Click Menu Mode by unchecking [Use ScanSnap Quick Menu] on the Right-Click Menu.
Why do vertical lines appear in the scanned image with Fujitsu ScanSnap S510 Scanner?
To address vertical lines appearing in scanned images, clean the inside of the ADF.
How to remove vertical lines from Fujitsu ScanSnap S510 Scanner images?
If vertical lines appear in the scanned image from your Fujitsu Scanner, it is likely that the inside of the ADF is dirty. Clean the inside of the ADF following the instructions in '5. Daily Care'.
Why are my Fujitsu ScanSnap S510 images not showing up?
If scanned images from your Fujitsu Scanner are not displayed on the screen, and 'Allow automatic blank page removal' is enabled, it's possible that nearly blank documents with few characters are being mistakenly recognized as blank pages and removed. To resolve this, right-click the 'ScanSnap Manager' icon on the task bar, select [SCAN Button Settings] -> [Scanning] tab, click the [Option] button, and then clear the 'Allow automatic blank page removal' checkbox.
Why Fujitsu ScanSnap S510 image scanned is too light or too dark?
If the scanned image from your Fujitsu Scanner is too light or too dark, adjust the "Brightness" setting under [Scanning] - [Option] in the "ScanSnap Manager - Scan and Save Settings" dialog box. This applies to black and white scanning only.
How to fix a part of the document does not appear in the scanned image with Fujitsu ScanSnap S510?
If a part of the document does not appear in the scanned image with your Fujitsu Scanner, clear the check box for "Allow automatic blank page removal" on [Option] of the [Scanning] tab of [Scan and Save Settings].
Why is paper not fed properly in my Fujitsu ScanSnap S510 Scanner?
If paper is not being fed properly or is stopping midway in your Fujitsu Scanner, it could be due to a dirty Pick roller. Clean the Pick roller following the instructions in '5.3. Cleaning Inside of the scanner'. Alternatively, the Pick roller might be worn out, requiring replacement as described in '6.3. Replacing the Pick Roller'. Check for and remove any debris from the document feeding path. Also, ensure the loaded documents meet the conditions described in section 3.2 of the ‘ScanSnap S510 Operator’s Guide’; if not, try slightly pushing the first sheet or changing the document's insertion direction.
Why can't I open files from my Fujitsu Scanner?
If files created by using the ScanSnap cannot be opened with a specified application, verify the location of the Image saving folder. If the folder is specified on another personal computer or a hard disk on the network, this could be the problem. Delete any corrupted files, if any, and then retry scanning.
What to do if scanning does not start on Fujitsu ScanSnap S510?
If scanning doesn't start on your Fujitsu Scanner, check that the USB cable is correctly connected, especially if using a hub (ensure the hub has power). Disconnect and reconnect the power cable, waiting at least 5 seconds. If the ScanSnap Manager icon isn't visible, start it from [Start] > [All Programs] > [ScanSnap Manager] > [ScanSnap Manager]. Additionally, close the "ScanSnap Manager - Scan and Save Settings" window before scanning.
General| Film scanning | No |
|---|---|
| Color scanning | Yes |
| Input color depth | - bit |
| Maximum scan size | 216 x 356 mm |
| Scanner type | Sheet-fed scanner |
| Sensor type | CCD |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5, B6 |
| Maximum ISO A-series paper size | A4 |
| Auto document feeder (ADF) input capacity | 50 sheets |
| USB version | 2.0 |
| Standard interfaces | USB 2.0 |
| Minimum storage drive space | 512 MB |
| Minimum system requirements | Windows 2000/ XP/ Vista |
| Sustainability certificates | ENERGY STAR |
| Power requirements | AC 100V to 240V, 50 / 60 Hz |
| Operating temperature (T-T) | 5 - 35 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Certification | RoHS |
Weight and Dimensions| Weight | 2700 g |
|---|
Details important information for safe and correct product operation, including warning symbols.
Instructions to verify all items are present after unpacking the scanner and contact support if missing.
Guides through the installation process of necessary software like ScanSnap Manager, Acrobat, etc.
Provides steps for connecting the scanner to a computer via power and USB cables.
Guides on how to modify various scanning parameters through ScanSnap Manager settings.
Covers various settings and operations within the ScanSnap Manager software.
Step-by-step instructions for safely removing jammed documents from the scanner.
A guide to diagnosing and resolving common scanner issues and symptoms.
Detailed steps for cleaning internal components like ADF glass, rollers, and pad ASSY.
Step-by-step instructions for replacing the Pad ASSY consumable.
Detailed procedure for replacing the pick roller consumable on the scanner.
To Next Page