FUTABA 14SG - AIL to CMBFLP; Mixing Rate Adjustment; Link Mode Setting

122
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button. Or the
HOME/EXIT button is
pushed.
<SensorTouch™>
RETURN
AIL3
(ChipAileron)
AIL4
(ChipAileron)
AIL1
(MainAileron)
AIL2
(MainAileron)
FLP2
(CamberFlap)
FLP1
(CamberFlap)
AIL to CMBFLP
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUDLOHURQV IODSVRU
more
This mix operates the camber flaps (FLP1/2)
in the aileron mode. When the aileron stick
is manipulated, the ailerons and camber flaps
perform aileron operation simultaneously to
VLJQL¿FDQWO\LPSURYHWKHUROOD[LV
ŏ7KHDLOHURQOHIWULJKWPL[LQJUDWHRIHDFKÁDSVHUYR
FDQEHLQGHSHQGHQWO\DGMXVWHG
ŏ$Q212))VZLWFKFDQEHVHW
ŏ/LQNLQJLVSRVVLEOH/LQNWKLVPL[WRRWKHUPL[HV
ŏ$GMXVWPHQWRIHDFK
ÁDSVHUYR
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGWRXFK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
touch sensor.
*The display blinks.
Touch the RTN button to activate the
IXQFWLRQDQGUHWXUQWRWKHFXUVRUPRGH21
LVGLVSOD\HG
When selecting a switch, move the cursor to
WKH>6:@LWHPDQGWRXFKWKH571EXWWRQWR
call the selection screen. Select the switch
DQGVHWLWV21GLUHFWLRQ$OZD\V21DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
 0RYHWKHFXUVRUWR WKHIODS)/3aOHIW
or right item according to the wing type
and touch the RTN button to switch to the
GDWDLQSXWPRGH$GMXVWWKHPL[LQJUDWH
independently by scrolling the touch sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Ɣ/LQNPRGHVHWWLQJ
When linking a mix, move the cursor to the
>/,1.@LWHPDQGWRXFKWKH571EXWWRQWR
switch to the data input mode. Select the
ON mode by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to set the link mode
and return to the cursor mode.
ŏ6HOHFW>$,/WR&0%)/3@DWWKH0RGHO
menu and access the setup screen
shown below by touching the RTN
button.
*The display screen is an example. The actual
screen depends on the model type.
Scrolling
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
(Glider: Currently selected condition name)