FUTABA 14SG - Gyro Sensitivity and Mode Switching; Pitch to RUD Mixing Setting; Throttle Hold Setting; Throttle Cut Setting

48
<Model Basic Setting Procedure>
function from the Model Menu, and set the curve
for each condition. (At initial setting, this function
is in the "INH" state. To use it, set it to the "ON"
state.)
6HWWLQJH[DPSOH!
Activate the mixing curve of each condition with
the condition select switch.
$FXUYHVHWWLQJH[DPSOHLVVKRZQEHORZ
ŏ3LWFKWR58'PL[LQJFXUYH1RUPDO
8VHWKHKRYHULQJV\VWHPDQGVHWWKLVFXUYHWR
PDWFKWDNHRIIDQGODQGLQJDQGYHUWLFDOFOLPEDWD
FRQVWDQWVSHHG
ŏ3LWFKWR58'PL[LQJ,GOHXS
8VHWKLVFXUYHLQVWDOOWXUQORRSDQGDGMXVWLWVRWKH
IXVHODJHLVIDFLQJVWUDLJKWDKHDGZKHQKHDGLQJ
LQWRWKHZLQG
ŏ3LWFKWR58'PL[LQJ+ROG
7KLVIXQFWLRQ LV VHW VR WKDW WKH IXVHODJHLVIDFLQJ
VWUDLJKWDKHDG DW VWUDLJKW OLQH DXWR URWDWLRQ 7KH
SLWFKRIWKHWDLOURWRUEHFRPHVQHDUO\
º

9. Throttle hold setting
*If throttle hold is necessary, please refer to the THR HOLD
function.
10. Throttle cut setting
Throttle cut provides an easy way to stop the
HQJLQHE\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFN
at idle. The action is not functional at high throttle
to avoid accidental dead sticks. The switch’s
location and direction must be chosen, as it defaults
to NULL.
*With throttle stick at idle, adjust the cut position until the
engine consistently shuts off, but throttle linkage is not
binding.
6ZDVK0L[FRUUHFWVDLOHURQHOHYDWRUDQG
pitch interaction
The swash mix function is used to correct the
swash plate in the aileron (Left/Right Cyclic)
and elevator (Forward/Aft Cyclic) direction
corresponding to each operation of each condition.
6. D/R function
D/R function is used to adjust the throw and
operation curve of aileron, elevator and rudder for
each condition.
*For throttle and pitch curve settings, refer to the afore-
mentioned "Throttle/Pitch curve setting"
7KLVLVQRUPDOO\XVHGDIWHU(QG3RLQWKDVGH¿QHG
the maximum throw directions.
*\URVHQVLWLYLW\DQGPRGHVZLWFKLQJ
The gyro sensitivity and mode switching
function is utilized to adjust the gyro mixing of the
model, and can be set for each condition.
ŏ 1RUPDOFRQGLWLRQKRYHULQJ*\URVHQVLWLYLW\
PD[LPXP
ŏ ,GOHXS,GOHXS7KURWWOHKROG*\UR
VHQVLWLYLW\PLQLPXP
ŏ +RZHYHUGXULQJDXWRURWDWLRQVZLWKDWDLO
GULYHQKHOLFRSWHUWKLVIXQFWLRQPD\QRWKDYH
DQ\HIIHFWRQWKHKLJKJ\URVHQVLWLYLW\
3LWFKWR58'PL[LQJVHWWLQJ
Note: When using a Futaba GY Gyro, or other
heading hold gyro, this Pitch to RUD mixing
should not be used. The reaction torque is
corrected by the gyro. When operating the
gyro in the AVCS mode, the mixed signal will
cause neutral deviation symptoms and the
gyro will not operate normally.
Use this function when you want to suppress
the torque generated by the changes in the pitch
and speed of the main rotor during pitch operation.
Adjust it so that the nose does not swing in the
rudder direction. However, when using a heading
hold gyro like those shown above, do not use Pitch
to rudder mixing.
Activate the Pitch to rudder (Pit -->RUD) mixing