FUTABA 14SG - ELE to Camber

129
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button. Or the
HOME/EXIT button is
pushed.
<SensorTouch™>
RETURN
ELE to CAMBER
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUDLOHURQVRUPRUH
This function is used when you want to mix the
FDPEHUÀDSVZLWKHOHYDWRURSHUDWLRQ:KHQXVHG
the flaps are lowered by up elevator, and lift is
increased.
ŏ,QÁLJKWPL[LQJFDQEHWXUQHG212))E\DVVLJQLQJ
WKLVWRDVZLWFK$OZD\V21DW>@VHWWLQJ
ŏ7KHPL[LQJUDWHFDQEHDGMXVWHG
ŏ7KH SRLQW WKDW KDV OLWWOH HIIHFW QHDU WKH QHXWUDO
SRVLWLRQRI WKH HOHYDWRU VWLFN FDQ EHDGMXVWHG
*OLGHURQO\
1RWH7KHHOHYDWRURQWKHWDLOOHVVZLQJZLOODOVR
EHHIIHFWHGZKHQWKLVPL[LVDFWLYDWHG
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the up or down mixing
rate item for each servo and touch the RTN
button to switch to the data input mode.
$GMXVWWKHUDWHLQGHSHQGHQWO\E\VFUROOLQJ
the touch sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGWRXFK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
touch sensor.
*The display blinks.
Touch the RTN button to activate the
IXQFWLRQDQGUHWXUQWRWKHFXUVRUPRGH21
LVGLVSOD\HG
When setting a switch, move the cursor to
WKH>6:@LWHPDQGWRXFKWKH571EXWWRQWR
call the selection screen. Select the switch
DQGVHWLWV21GLUHFWLRQ$OZD\V21DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ5DQJHVHWWLQJ*OLGHURQO\
 0RYHWKHFXUVRU WRWKH>5$1*(@LWHP DQG
hold the elevator stick to the desired position
XSSHURUORZHUVLGHDQGWKHQWRXFKWKH571
button for one second to set the range.
*The mixing does not work near neutral of the elevator stick.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
(Glider: Currently selected condition name)
ŏ6HOHFW>(/(WR&$0%(5@DWWKH0RGHOPHQX
and access the setup screen shown below
by touching the RTN button.
*The display screen is an example.
The actual screen depends on the
model type.
Scrolling
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH