FUTABA 14SG - Model Selection; Model Addition

69
<Functions of Linkage Menu>
ŏ6HOHFWWKHIXQFWLRQ QDPH
DQGUHWXUQWRWKH/LQNDJH
PHQXE\WRXFKLQJWKH
RTNEXWWRQ 2UWKH
HOME/EXITEXWWRQLV
SXVKHG
<SensorTouch™>
RETURN
MODEL SELECT
7KH0RGHO6HOHFWLRQIXQFWLRQ SHUIRUPVPRGHODGGLWLRQVHOHFWLRQ
GHOHWLRQFRS\DQGPRGHOQDPHVHWWLQJ
This function is used to load the settings of the
desired model into the T14SG’s memory.
The settings may be selected from either the
transmitter’s internal memory or an SD card.
Remember that up to 30 model memories are available
in the transmitter.
The name of the model stored in the transmitter and
the SD card may be changed. This can be very useful
to tell different models settings apart. Each model name
can be as long as 10 characters, and the model name
always appears in the display screen.
The Copy function is used to copy parameters,
settings, etc. from one model data into a second
memory. It may be used for getting a head-start on
setting up models with almost the same settings (only
GLIIHUHQFHVQHHGWREHPRGL¿HGLQVWHDGRIHQWHULQJWKH
complete model from scratch). Also, this function may
be used to make a backup copy of a model setup before
any changes are made.
*T14SG can use the model data of T8FGS for SD card,
copying it. However, the model data of T14SG cannot be
used by T8SG (S).
Model selection
*Model data saved on the transmitter memory other than the
model currently used can be selected.
0RYHWKHFXUVRUWRWKHVDYHGHVWLQDWLRQ
GLVSOD\7;RU&$5'DQGWRXFKWKH571
EXWWRQWRVZLWFKWRWKHGDWDLQSXWPRGH
 6HOHFWWKHVDYHGHVWLQDWLRQE\VFUROOLQJWKH
WRXFKVHQVRUDQGWRXFKWKH571EXWWRQ
 >7;@7UDQVPLWWHUPHPRU\
 >&$5'@6'FDUG
$IWHUPRYLQJWKHFXUVRUWRWKHGHVLUHGPRGHO
LQWKHPRGHOOLVWWRXFKWKH571EXWWRQ
0RYHWR>6(/(&7@
7RXFKWKH571EXWWRQ$FRQILUPDWLRQ
PHVVDJHLVGLVSOD\HG7RXFKWKH571EXWWRQ
IRURQHVHFRQGDQGVHOHFWLRQLVFRPSOHWH
*Transmission stops and then starts in the new model.
Model addition
*A new model can be added to the transmitter memory. It can
not be added to the SD card.
0RYHWKHFXUVRUWR>1(:@
7RXFKWKH571EXWWRQ$FRQILUPDWLRQ
PHVVDJHDSSHDUV7RXFKWKH571EXWWRQIRU
RQHVHFRQG
*The model type setup screen and frequency setup screen are
DXWRPDWLFDOO\GLVSOD\HG&RQ¿UPRUFKDQJHWKHPRGHOW\SH
and SYSTEM mode.
*Transmission stops and then starts in the new model.
*The added model appears in the model list of the model
select setup screen.
*Link is required when a new model is
made from a model selection.
ŏ6HOHFW>02'(/6(/(&7@LQWKH/LQNDJHPHQX
DQGDFFHVVWKHVHWXSVFUHHQVKRZQEHORZE\
WRXFKLQJWKH571EXWWRQ
*The display screen is an example. The
screen depends on the model type.
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
0RGHOOLVW
&XUUHQWPRGHO