FUTABA 14SG - RUD to AIL

125
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button. Or the
HOME/EXIT button is
pushed.
<SensorTouch™>
RETURN
RUDDER2
RUDDER
RUDDER
V-TAIL
RUDDER2
Winglet
RUDDER1
Winglet
atFlyingwing
atFlyingwing
() ()
AIL3
AIL3
(ChipAileron)
(ChipAileron)
AIL1
(MainAileron)
AIL2
(MainAileron)
RUD to AIL
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUJHQHUDO
This function is used when you want to mix
the ailerons with rudder input. It is used when
rudder is applied during roll maneuvers such
as, knife edge flight. It can be used to turn or
bank scale models, large models, etc. like a full-
size aircraft.
ŏ0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG212))E\
VHWWLQJDVZLWFK$OZD\V21DW>@VHWWLQJ
ŏ/LQNLQJFDQEHVHW/LQNWKLVPL[WRRWKHUPL[HV
ŏ7KHPL[LQJUDWHFDQDOVREHDGMXVWHG
ŏ$SRLQWFXUYHFDQEHVHWDWDLUSODQHPRGHOW\SH
ŏ6HOHFW>58'WR$,/@DWWKH0RGHO
menu and access the setup screen
shown below by touching the RTN
button.
*The display screen is an example.
The actual screen depends on the
model type.
Scrolling
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGWRXFK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
touch sensor.
*The display blinks.
Touch the RTN button to activate the
IXQFWLRQDQGUHWXUQWRWKHFXUVRUPRGH21
LVGLVSOD\HG
When setting a switch, move the cursor to
WKH>6:@LWHPDQGWRXFKWKH571EXWWRQWR
call the selection screen. Select the switch
DQGVHWLWV21GLUHFWLRQ$OZD\V21DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQWJOLGHU
Move the cursor to the left or right item
and touch the RTN button to switch to the
GDWDLQSXWPRGH$GMXVWWKHPL[LQJUDWH
independently by scrolling the touch sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Ɣ/LQNPRGHVHWWLQJ
To activate the link mixing, move the cursor
WRWKH>/,1.@LWHPDQGWRXFKWKH571EXWWRQ
to switch to the data input mode. Select the
ON mode by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to set the link mode
and return to the cursor mode.
(Glider: Currently selected condition name)