FUTABA 14SG - Gyro Type Selection; Operation Mode Selection (GYA Gyro); Sensitivity Setting (Gyro)

138
<Model Menu (Airplane/Glider Functions)>
When setting a rate selection switch, move
the cursor to the switch item and touch the
RTN button to access the selection screen.
Select the switch and set its ON direction.
$OZD\V21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ*\URW\SHVHOHFWLRQ
Move the cursor to the gyro type selection
item and touch the RTN button to switch to
the data input mode. Select the gyro type
by scrolling the touch sensor.
 >*<@:KHQD)XWDED*<$J\URLVXVHG
 >1250@:KHQXVLQJVRPHWKLQJRWKHUWKDQ
)XWDED*<$J\URLVXVHG
Touch the RTN button to change the gyro
type and return to the cursor mode.
*When a Futaba GYA gyro is used and [GY] type is selected,
the sensitivity set value is directly read in both the AVCS
and NORM modes.
Ɣ2SHUDWLRQPRGHVHOHFWLRQ*<$J\UR
Move the cursor to the operation mode
selection item and touch the RTN button
to switch to the data input mode. Select
the operation mode by scrolling the touch
sensor.
 >$9&6@$9&6PRGH
 >1250@1RUPDOPRGH
Touch the RTN button to change the
operation mode and return to the cursor
mode.
Ɣ6HQVLWLYLW\VHWWLQJ
Move the cursor to the sensitivity icon and
touch the RTN button to switch to the data
input mode.
 $GMXVWWKHVHQVLWLYLW\E\VFUROOLQJWKHWRXFK
sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the
sensitivity is reset to the initial value.)
Touch the RTN button to return to the cursor
mode.
([DPSOH6HWWLQJWKUHHD[LVXVLQJD*<$DQG*<$
ŏ:LQJW\SH$LOHURQVHUYRVPRXQWHGIXVHODJHVHOHFWHG
ŏ6HW
5CH → GYRO
*<$$,/
7CH → GYRO2
*<$(/(
8CH → GYRO3
*<$58'
CTRL
andTRIM → [--]
DWWKH)XQFWLRQPHQXRIWKH/LQNDJHPHQX
ŏ*<52VHWWLQJRIWKH0RGHOPHQX
*Set so that Rate 1 is turned on at the back position of switch E and Rate 3 is turned ON at the front position. Since
switch E is turned OFF at the center, Rate 2 remains [INH].
R7008SB
Rudderservo
Elevatorservo
GYA430
GYA431
GYA431
Aileronservo
S.BUS/S.BUS2port
:KHQD6%86SRUWLV
XVHG56%&+0RGH
LVVHWWR0RGH%>'@
GAIN0％
AVCS
NORMAL
WhenAVCSisusedwe
recommendthatthe
sensitivityCHbesetto
the3-position.
Rate GYRO GYRO ２ GYRO ３ TYPE ACT/INH SW
#1 AVCS:60% AVCS:60% AVCS:60% GY OFF/ON SE
#2 INH
#3 NORM:60% NORM:60% NORM:60% GY ON/OFF SE