FUTABA 14SG - RUD to ELE

144
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button. Or the
HOME/EXIT button is
pushed.
<SensorTouch™>
RETURN
RUD to ELE
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJHQHUDO
This function is used when you want to mix
elevator operation with rudder operation. It is used
to correct undesirable tendencies when rudder is
applied in rolling maneuvers such as, knife edge
ÀLJKW
ŏ0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG212))E\
VHWWLQJDVZLWFK$OZD\V21DW>@VHWWLQJ
ŏ/LQNPL[LQJFDQEHVHW/LQNVWKLVPL[WRRWKHUPL[HV
ŏ6HOHFW>58'WR(/(@DWWKH0RGHO
menu and access the setup screen
shown below by touching the RTN
button.
Scrolling
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGWRXFK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
touch sensor.
*The display blinks.
Touch the RTN button to activate the
IXQFWLRQDQGUHWXUQWRWKHFXUVRUPRGH21
LVGLVSOD\HG
When selecting a switch, move the cursor to
WKH>6:@LWHPDQGWRXFKWKH571EXWWRQWR
call the selection screen. Select the switch
DQGVHWLWV21GLUHFWLRQ$OZD\V21DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
ƔSRLQWFXUYHVHWWLQJDLUSODQH
>&XUYHUDWHVHWWLQJ@
1. Move the cursor to the curve rate setting
LWHPOHIWVLGH\RXZDQWWRDGMXVWDQGWRXFK
the RTN button to switch to the data input
mode.
 $GMXVWWKHUDWHE\VFUROOLQJWKHWRXFKVHQVRU
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>0RYLQJFXUYHSRLQW@
1. Move the cursor to the curve point setting
LWHP\RXZDQWWRDGMXVWDQGWRXFKWKH571
button to switch to the data input mode.
 $GMXVWWKHFXUYHSRLQWE\VFUROOLQJWKHWRXFK
sensor.
 $GMXVWPHQWUDQJH8SWRLQIURQWRIWKH
DGMRLQLQJSRLQW
*When the RTN button is touched for one second, the curve
position is reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>'HOHWLQJUHWXUQLQJFXUYHSRLQW@
Move the cursor to the curve point setting
LWHP\RXZDQWWRGHOHWHUHWXUQDQGWRXFK
the RTN button for one second.
Ɣ/LQNPRGHVHWWLQJ
When selecting the link mixing, move the
FXUVRUWRWKH>/,1.@LWHPDQGWRXFKWKH571
button to switch to the data input mode.
Select the ON mode by scrolling the touch
sensor.
*The display blinks.
Touch the RTN button to set the link mode
and return to the cursor mode.