FUTABA 14SG - Trim Offset Rate Adjustment; Auto Switch Selection

134
<Model Menu (Airplane/Glider Functions)>
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGWRXFK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
touch sensor.
*The display blinks.
Touch the RTN button to activate the
IXQFWLRQDQGUHWXUQWRWKHFXUVRUPRGH21
LVGLVSOD\HG
When setting a switch, move the cursor to
the switch item and touch the RTN button
to access the selection screen. Select the
VZLWFKDQGVHWLWV21GLUHFWLRQ$OZD\V21
DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ7ULPRIIVHWUDWHDGMXVWPHQW
Move the cursor to the aileron, flap or
elevator rate item and touch the RTN button
WRVZLWFKWRWKHGDWDLQSXWPRGH$GMXVWWKH
rate independently by scrolling the touch
sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Ɣ&RQGLWLRQGHOD\VHWWLQJ
 0RYHWKHFXUVRUWRWKH>&21''(/$<@LWHP
and touch the RTN button to switch to the
GDWDLQSXWPRGH$GMXVWWKHFRQGLWLRQGHOD\
by scrolling the touch sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the servo
operation position is reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
When setting a cut switch, move the cursor
WRWKH>&876:@LWHPDQGWRXFKWKH571
button to access the selection screen. Select
WKHVZLWFKDQGVHWLWV21GLUHFWLRQ$OZD\V
21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ6HUYRVSHHGVHWWLQJ
Move the cursor to the aileron, flap or
elevator speed item and touch the RTN
button to switch to the data input mode.
 $GMXVWWKHUDWHE\VFUROOLQJWKHWRXFKVHQVRU
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHaPD[LPXPGHOD\
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to activate the
function and return to the cursor mode.
Ɣ$XWRVZLWFKVHOHFWLRQ
When selecting an auto switch, move the
FXUVRUWRWKH>$8726:@LWHPDQGWRXFKWKH
RTN button to access the selection screen.
Select the switch and set its ON direction.
$OZD\V21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
AIL3
(ChipAileron)
AIL4
(ChipAileron)
AIL1
(MainAileron)
AIL2
(MainAileron)
FLP2
(CamberFlap)
FLP1
(CamberFlap)
ELEVATOR
ELEVATOR2
V-TAIL
ELEVATOR
ELEVATOR2
AILVATOR
FLP3
(BrakeFlap)
FLP4
(BrakeFlap)