FUTABA 14SG - Elevator Compensation Curve Adjustment; Servo Speed Setting

132
<Model Menu (Airplane/Glider Functions)>
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGWRXFK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
touch sensor.
*The display blinks.
Touch the RTN button to activate the
IXQFWLRQDQGUHWXUQWRWKHFXUVRUPRGH21
LVGLVSOD\HG
When setting a switch, move the cursor to
WKH>6:@LWHPDQGWRXFKWKH571EXWWRQWR
call the selection screen. Select the switch
DQGVHWLWV21GLUHFWLRQ$OZD\V21DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ5DWHDGMXVWPHQW
Move the cursor to the aileron, flap or
elevator rate item and touch the RTN button
WRVZLWFKWRWKHGDWDLQSXWPRGH$GMXVWWKH
rate independently by scrolling the touch
sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa(OHYDWRU
a
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Ɣ(OHYDWRUFRPSHQVDWLRQFXUYHDGMXVWPHQW
2XWSXW< 3RVLWLRQ;
Offset point )L[HG )L[HGRIIVHW
SRVLWLRQ
,QWHUPHGLDWHSRLQW Settable Settable
(QGSRLQW Settable )L[HG
* The range where mixing does not work close to the neutral
position of the elevator stick can be adjusted. (Glider only)
*When offset is set, the curve is initialized.
Ɣ5HIHUHQFHSRLQWDGMXVWPHQW
 0RYHWKHFXUVRUWRWKH>2))6(7@LWHPDQG
hold the airbrake stick to the desired position
and then touch the RTN button for one
second to set the butterfly operational
reference point.
 ,QLWLDOYDOXHXSSHUVLGH
 $GMXVWPHQWUDQJHa
Ɣ6HUYRVSHHGVHWWLQJ
Move the cursor to the aileron, flap or
elevator speed item and touch the RTN
button to switch to the data input mode.
 $GMXVWWKHUDWHE\VFUROOLQJWKHWRXFKVHQVRU
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHaPD[LPXPGHOD\
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to activate the
function and return to the cursor mode.
AIL3
(ChipAileron)
AIL4
(ChipAileron)
AIL1
(MainAileron)
AIL2
(MainAileron)
FLP2
(CamberFlap)
FLP1
(CamberFlap)
ELEVATOR
ELEVATOR2
V-TAIL
ELEVATOR
ELEVATOR2
AILVATOR
FLP3
(BrakeFlap)
FLP4
(BrakeFlap)